a
L
F
D
ĉ
Ĉ
S
=
V
D
ĉ
Ĉ
S
=
I
D
ĉ
Ĉ
S
=
/
D
ĉ
Ĉ
S
=
K
D
ĉ
Ĉ
S
=
c
D
ĉ
Ĉ
S
=
:
D
ä
@
D
Z
D
ĉ
Ĉ
S
=
2
>
ĉ
/
LF
LF
LF
LF
/
c
:
ü
LF
Ĉ
I
$
a
a
a
a
>
>
$
11
What to do if ...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not
dispensed.
–
$
Start
/Reload not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a
page 10
.
– Supply hose kinked or trapped?
ʑ
Washing machine door
cannot be opened.
– Safety function active. Programme stopped?
a
page 4
.
–
(without final spin) selected?
a
page 3, 4.
– Can be opened by emergency release only?
a
page 9.
ʑ
Programme does not
start.
–
$
Start
/Reload or
Ready in
time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate
a
page 5
.
ʑ
Detergent solution is not
drained.
–
(without final spin) selected?
a
page 3, 4.
– Clean the detergent solution pump
a
page 10
.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the
drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin
result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled
the spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
–
S
Reduced Ironing
selected?
a
page 5.
– Selected speed too low?
a
page 5
.
ʑ
The programme
duration changes
during the wash cycle.
– Not a fault – the programme sequence is optimised for the
particular wash process. This may result in changes to the
programme duration in the display field.
ʑ
Spin cycle performed
several times.
– Not a fault - unbalanced load detection system adjusts the
imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
a
page 9
.
ʑ
Odour formation in the
washing machine.
– Run programme
LF
Cottons 90 °C
without laundry. Use
standard detergent.
ʑ
Status display
³
1
flashes. Foam may be
coming out of the
detergent drawer.
– Too much detergent used? Mix 1 tablespoon of fabric softener
with ½ litre of water and pour into dispenser
II
(not for outdoor and
down-filled textiles!).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and
“wandering” during the
spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet
a
Installation instructions
.
– Transportation safety devices removed? Remove the
transportation safety devices
a
Installation instructions
.
ʑ
Noises during spin and
drain cycles.
– Clean detergent-solution pump
a
page 10.
ʑ
Display panel/indicator
lamps do not function
during operation.
– Power cut?
– Fuses triggered? Reset/change the fuse.
– If the fault occurs repeatedly, call customer services.
ʑ
Programme sequence
longer than usual.
– Not a fault - unbalanced load detection system adjusts imbalance
by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional
rinse cycle.
ʑ
Detergent residues
on the laundry.
– Occasionally, phosphate-free detergents contain water-insoluble
residues.
– Use the
2
Rinse
cycle or brush out the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Off
and remove the mains plug from the socket.
– Turn off the water supply and call customer services
a
Installation instructions.
Washing machine
en
Instruction manual
