a
c
c
c
c
c
:
ä
2
c
>
@
@
A
B
B
B
:
c
~
a
a
a
>
>
11
What to do if ...
ʑ
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
ʑ
No water supply.
Detergent not dispensed.
–
Inicio
(Start)
not selected?
– Tap not turned on?
– Filter blocked? Clean the filter
a
page 10.
– Supply hose kinked or trapped?
ʑ
Washing machine door cannot
be opened.
– Safety function active. Wait approx. 2 minutes.
–
(without final spin) selected?
a
page 3, 4.
ʑ
Programme does not start.
–
Inicio
(Start)
selected?
– Washing machine door closed?
ʑ
Detergent solution is not
drained.
–
(without final spin) selected?
a
page 3, 4.
– Clean the detergent solution pump
a
page 10.
– Clean the waste pipe and/or drainage hose.
ʑ
Water not visible in the drum.
– Not a fault - water below the visible area.
ʑ
Unsatisfactory spin result.
Laundry wet/too damp.
– Not a fault - the unbalanced-load detection system has cancelled the spin cycle
because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum.
– Too low a speed selected?
a
page 5
.
ʑ
Spin cycle performed several
times.
– Not a fault - unbalanced load detection system adjusts the imbalance.
ʑ
Residual water in the
compartment for care
products.
– Not a fault - the action of the care product is not affected.
– Clean the insert if necessary
a
page 9
.
ʑ
Odour formation in the washing
machine.
– Run programme
Algodón/Algodão
ü
(Cottons) 90 °C
without laundry. Use
standard detergent.
ʑ
Foam escaping from the
detergent drawer.
– Too much detergent used?
If foam is escaping from the detergent drawer:
Mix 1 tablespoon of fabric softener with ½ litre of water and pour into
compartment II
(not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
ʑ
Intense noise formation,
vibrations and “walking” during
the spin cycle.
– Are the appliance feet fixed?
Secure the appliance feet
a
Installation instructions
.
– Transportation safety devices removed?
Remove the transportation safety devices
a
Installation instructions
.
ʑ
Noises during spin and drain
cycles.
– Clean detergent-solution pump
a
page 10.
ʑ
The indicator lights do not
function during operation.
– Power cut?
– Fuses tripped? Reset/change the fuse.
– If the fault occurs repeatedly, call the after-sales service.
ʑ
Programme sequence longer
than usual.
– Not a fault - unbalanced load detection system adjusts imbalance by repeatedly
distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse cycle.
ʑ
Detergent residues on the
laundry.
– Occasionally, phosphate-free detergents contain water-insoluble residues.
– Select
2
(Rinse)
or brush out the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to
Stop (Off)
and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
a
Installation instructions.
en
operating instructions
Washing machine
WAE20067EE ...
