Bosch VideoJet 8004 Installation And Operating Manual Download Page 67

Page: 67 / 164

VideoJet 8008 / VideoJet 8004

| Installation and Operating Manual

| 67

Bosch Security Systems | 2006-07 | V1.5

Configuration using a Web browser

Unit time:

Enter the current time or click the

Synchr. PC

button to copy your computer's

system time to the unit.

Time server

The unit can receive the time signal of a time server via the Time Server Protocol
(RFC 868) and set the internal clock accordingly. The unit polls the time signal
automatically every ten minutes.

Time zone:

Select the time zone in which your system is located.

Time settings:

Check this box during daylight saving time to include the time change. Deacti-
vate the box again to return to winter time.

Time server IP address:

Enter the IP address of a time server that uses the RFC 868 protocol.

Summary of Contents for VideoJet 8004





































































































































































Search results

Summary of Contents for VideoJet 8004

Reviews:

Bosch VideoJet 8004, Installation And Operating Manual, Page: 67 / 164

Search results

Summary of Contents for VideoJet 8004

Reviews: