Bosch SRS2IKW04G User Manual Download Page 33

Page: 33 / 56

Basic settings

You can configure the appliance to meet your needs.

Overview of basic settings

The basic settings depend on the features of your appliance.

Basic setting

Selection

Description

Water hardness

Scale with 4 levels

Set the water hardness.

→

"Setting the water softening

system", Page 23

Rinse aid disp.

Scale with 4 levels

Set the amount of rinse aid to
be dispensed or switch off.

→

"Setting the amount of rinse

aid", Page 25

Extra Dry

On
Off

Switch Extra Dry on or off for
each operation.
For a better drying result the
temperature in the final rinse is
increased. This may increase
the running time slightly.

Note:

Please take care with del-

icate tableware.

→

"Setting Extra Dry",

Page 33

Factory setting

Reset

Restore changed settings to the
factory settings.
The settings for initial start-up
must be configured.

→

"Restoring factory settings",

Page 33

Factory setting (may vary according to model)

Setting Extra Dry

Press ⁠.

To open the appliance settings,
press

for 3 seconds.

is flashing on the display.

Press

repeatedly until

and

flash in the display.

Press

repeatedly until the

LEDs show the right value.
If "LED A" →

Page 15

is not lit, Ex-

tra Dry is switched off.

If "LED A" →

Page 15

is lit, Extra

Dry is switched on.

To save the settings, press

for 3 seconds.

Restoring factory settings

Press ⁠.

To open the appliance settings,
press

for 3 seconds.

is flashing on the display.

Summary of Contents for SRS2IKW04G

























































Search results

Summary of Contents for SRS2IKW04G

Reviews:

Related manuals for SRS2IKW04G

Brands by name

Popular brands

Bosch SRS2IKW04G, User Manual

Search results

Summary of Contents for SRS2IKW04G

Reviews:

Related manuals for SRS2IKW04G

Brands by name

Popular brands