Bosch SPS2IKW04E User Manual Download Page 32

Page: 32 / 56

Basic settings

You can configure the appliance to meet your needs.

Overview of basic settings

The basic settings depend on the features of your appliance.

Basic setting

Selection

Description

Water hardness

Scale with 4 levels

Set the water hardness.

→

"Setting the water softening

system", Page 22

Rinse aid disp.

Scale with 4 levels

Set the amount of rinse aid to
be dispensed or switch off.

→

"Setting the amount of rinse

aid", Page 25

Extra Dry

On
Aus

Switch Extra Dry on or off for
each operation.
For a better drying result the
temperature in the final rinse is
increased. This may increase
the running time slightly.

Note:

Please take care with del-

icate tableware.

→

"Setting Extra Dry",

Page 32

Wi-Fi

On
Off

Switch the wireless network
connection on or off.

→

"Set Wi-Fi", Page 33

Remote start

Scale with 3 levels

Activate or deactivate remote
start.

→

"Set remote start", Page 33

Factory setting

Reset

Restore changed settings to the
factory settings.
The settings for initial start-up
must be configured.

→

"Restoring factory settings",

Page 33

Factory setting (may vary according to model)

Setting Extra Dry

Press ⁠.

To open the appliance settings,
press

for 3 seconds.

flashes in the display.

Press

repeatedly until

and

flash in the display.

Summary of Contents for SPS2IKW04E

























































Search results

Summary of Contents for SPS2IKW04E

Reviews:

Related manuals for SPS2IKW04E

Brands by name

Popular brands

Bosch SPS2IKW04E, User Manual

Search results

Summary of Contents for SPS2IKW04E

Reviews:

Related manuals for SPS2IKW04E

Brands by name

Popular brands