background image

Water softening system

 en

25

Do not use table salt.
Add the special salt to the dis-
penser.

a

Funnel 

1

Fill the dispenser right up with spe-
cial salt. The water in the dis-
penser is displaced and forced
out.

4.

Place the lid back on the dis-
penser and turn to close.

Switching off the water
softening system

If you find the special salt refill indic-
ator irritating, e.g. when using com-
bined detergents with salt replace-
ment substances, you can switch the
salt refill indicator off.

Note

To avoid damage to the appliance, only
switch off the water softening system in
the following cases:

¡

The water hardness is max. 26  °E
and you are using combined deter-
gents with salt replacement sub-
stances. According to manufactur-
ers, combined detergents with salt
replacement substances can gen-
erally only be used up to a water
hardness of 26  °E without adding
special salt.

¡

The water hardness is 0 - 8 °E.
You do not need to use special
salt.

1.

Press  ⁠.

2.

To open the basic settings, press

 for 3 seconds.

a

The display shows Hxx.

a

The display shows 

⁠.

3.

Press 

 repeatedly until the dis-

play shows H00.

4.

To save the settings, press

 for 3 seconds.

a

The water softening system is
switched off and the salt refill indic-
ator is deactivated.

Regeneration of the water
softening system

In order to obtain fault-free function of
the water softening system, the appli-
ance performs regeneration of the
water softening system at regular in-
tervals.
Regeneration of the water softening
system takes place before the end of
the main rinse cycle in all pro-
grammes. It will increase the run time
and consumption values, e.g. water
and electricity.

Overview of consumption values
with regeneration the water
softening system

Here you can find an overview of the
maximum additional run time and
consumption values during regenera-
tion of the water softening system.

Regeneration of the water softening
system after x rinse cycles

6

Additional run time in minutes

7

Additional water consumption in
litres

5

1

Depending on the appliance specifications

Summary of Contents for SMU4HVI72S





























































Reviews: