8
9
Setting
Factory setting Description
•
Water hardness
•
:
‹‹
-
•
:
‹ˆ
•
:
‹…
Setting the water hardness.
§
-Rinse Aid
§
:
‹‹
-
§
:
‹‡
§
:
ܠ
Dispenses the amount of rinse aid,
which affects drying (see above).
š
-Intensive drying
š
:
‹‹
-
š
:
‹‚
š
:
‹‹
/ off
Improved drying for glasses and
plastic, by increasing the tempera-
ture and length.
›
-Beep at cycle end
›
:
‹‹
-
›
:
‹„
›
:
‹ƒ
Adjust the sound level of the signal
beep at the end of the cycle.
‚
-Infolight®
*
‚
:
‹‹
-
‚
:
‹‚
‚
:
‹‚
/ on
Light projected on the floor to signal
active wash cycle. Set to on or off.
˜
-Auto power off
˜
:
‹‹
-
˜
:
‹ƒ
˜
:
‹‚
/ off after
one minute
Unit turns itself off after cycle is
complete, either after 1 minute,
˜
:
‹‚
or after 2 hours,
˜
:
‹ƒ
.
†
TimeLight®
*
†
:
‹‹
,
†
:
‹‚
†
:
‹‚
/ on
While a wash cycle is running,
status information is projected onto
the floor. Set to on or off.
ADJUSTING THE SETTINGS
1.
Press the On/Off button. Hold down button
A
(see pages 6-7) and press
Start until the display shows
•
:
‹
x (x can be any number).
2.
Release both buttons. The LED for the button
A
flashes and the digital
display shows the factory set value. Press
A
to choose the setting.
3.
Press buttons
B
or
C
(up or down) to change the setting.
4.
Press Start button to save the setting.
*
Depending on the model
USAGE TIPS FOR BEST RESULTS
Scrape
off
food,
but
do not
rinse.
Use rinse
aid
for better
drying.
Adjust
upper rack
as needed
for large
items.
PUSH
Do not
place
objects in
detergent
tray or
block it with
dishes
FREQUENTLY ASKED QUESTIONS
Q
:
Why is food left on dishes?
A
:
It is possible the dishes do not have adequate clearance between them.
Also, be sure nothing is blocking spray arm and that the filter is clean. Select an
intensive cleaning cycle.
Q
:
Why does the cycle run a long time?
A
:
1. Sensors in the dishwasher automatically increase the cycle time to ensure a
good wash when heavy soil is detected.
2. Incoming water may not be hot enough and the dishwasher has to heat it.
Q
:
Why is E:XX (X can be any number) displayed?
A
:
This is an error code. For example, E:22 indicates there is water in the sump
because the filter is blocked or needs cleaning. See the Use and Care Manual
for a list of error codes.
To access the full Use and Care Manual, go to:
www.bosch-home.com/us/service/get-support/owner-manuals.
Clean surfaces with damp cloth and mild soap.
NOTICE
:
Do not use abrasives or bleach based cleaners. Do not use stainless
steel cleaner on black stainless or anti-finger print surfaces.
Clean the filter 3-12 times a year, depending on usage.
1.
Unscrew the Large Object Trap as illustrated and remove the entire filter
system.
2.
Remove the micro-filter from the fine filter, rinse the filters under running
water clean with a soft brush.
3.
Reinstall the filter system in reverse sequence, align arrows.
1
2
MAINTENANCE TIPS
