Bosch SHP65TL5UC Repair Instructions Download | Manualshive

Page: 60 / 82

background image

702_58300000170749_ara_en_c

Page 60 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

5.18 Side trim strips

Side trim strips aren’t mounted with screws, but snap into slots in
tank front flanges. No tools are needed unless the dishwasher
needs to be pulled out for access.

5.18.1

Removing side trim strips

Tools needed: #2 Phillips screwdriver.

1.

Disconnect & pull out dishwasher

– section 5.1.5.1, if

necessary for access.

2. Twist trim strips away from dishwasher tank flange. Tabs

in trim strips snap into front tank flange slots

(below)

.

5.18.2

Installing side trim strips

1. Align hole in bottom of each trim strip with the hinge screw

(below)

. There is also a lip on the back of the hinge to

help line up the holes.

2.

Rotate trim strip into tank flange until the three (3) tabs
snap into corresponding tank flange slots.

5.19 Water (salt) softener (selected models)

5.19.1

Removing regeneration valve

Removing the regeneration valve saves time and money
compared to replacing the entire salt softener.

Tools needed: T20 Torx, #2 Phillips & small flat blade
screwdrivers

.

1.

Disconnect & pull out dishwasher

– section 5.1.5.1.

2. Remove water from the water level control and the water

softener to prevent leaking.

3. To remove the valve coil, rotate it ccw (i.e. to the left)

and pull it out from the softener

(below)

. The valve body

will remain in the softener.

«
...
58
59
60
61
62
...
»

Summary of Contents for SHP65TL5UC



















































































Reviews:

No comments

Related manuals for SHP65TL5UC

Brand: Haier Pages: 6

Brand: Haier Pages: 15

Brand: Haier Pages: 15

Brand: Haier Pages: 19

Brand: mabe Pages: 32

Brand: SCHOLTES Pages: 52

Brand: Hoonved Pages: 18

Brand: Manta Pages: 19

Brand: Atag Pages: 36

Brand: Hotpoint Pages: 60

Brand: Hotpoint Pages: 16

HG6085D137635QW

Brand: Hanseatic Pages: 82

Brand: oneConcept Pages: 36

Brand: V-ZUG Pages: 84

Brand: GE Pages: 48

Brand: Maytag Pages: 52

Brand: Indesit Pages: 72

Brand: Haier Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands