Bosch Rexroth lndraDrive HCS02 Series Project Planning Manual Download Page 72

Page: 72 / 382

Connection points power sections HCS02.1E-W0054, ‑W0070 (bottom)

mains connection

motor connection

motor temperature monitoring, motor holding brake

external braking resistor

XS2

shield connection motor cable

Fig.5-42:

Connection points power sections HCS02.1E-W0054, -W0070 (bottom)

DANGER

Lethal electric shock caused by live parts with more than 50 V!

Via the connection X3 (mains connection), connect the drive controller to the

equipment grounding conductor system.

Description of the Connection Points

The connection points are described in detail in chapter

8 Functions and Elec‐

trical Connection Points , page 241

Touch Guard

The touch guard is described in detail in chapter

9 Touch Guard at Devices ,

page 291

5.3

HCS03 Power Sections

5.3.1

Brief Description, Usage and Structure

Brief Description

The compact converters HCS03 are part of the Rexroth IndraDrive C product

range and are used to operate single axes.

62/369

Bosch Rexroth AG | Electric Drives

and Controls

Rexroth IndraDrive | Project Planning Manual

Power Sections for Converters - IndraDrive C

Summary of Contents for Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands

Bosch Rexroth lndraDrive HCS02 Series, Project Planning Manual

Search results

Summary of Contents for Rexroth lndraDrive HCS02 Series

Reviews:

Related manuals for Rexroth lndraDrive HCS02 Series

Brands by name

Popular brands