Bosch Rexroth IndraDrive X Operating Instructions Manual Download

Page: 68 / 140

10.2.3

XMQ1

Fig. 10-6:

Dimensional drawing XMQ1-WQ001

10.3

Mounting

Observe the minimum distances specified in the dimensional drawings. See

chapter 10.2 "Housing dimensions" on page 50

10.4

Dismounting

10.4.1

Dismounting steps

Lethal electric shock by live parts with more

than 50 V!

WARNING

Before working on live parts: De-energize installation and secure power

switch against unintentional or unauthorized re-energization.
Wait at least 30 minutes after switching off the supply voltages to allow

discharging.
Check whether voltage has fallen below 50 V before touching live parts!

Observe the discharge time before you start dismounting the device.

52/123

Mounting, dismounting and electrical installation

IndraDrive X Drive Controllers Power Sections XCS1, XMD1,

XMQ1

Bosch Rexroth AG R911392532_Edition 01

Summary of Contents for Rexroth IndraDrive X













































































































































Search results

Summary of Contents for Rexroth IndraDrive X

Reviews:

Related manuals for Rexroth IndraDrive X

Brands by name

Popular brands

Bosch Rexroth IndraDrive X, Operating Instructions Manual

Search results

Summary of Contents for Rexroth IndraDrive X

Reviews:

Related manuals for Rexroth IndraDrive X

Brands by name

Popular brands