Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 357

Page: 357 / 422

11.3.2

KCU02 diagnostic display

Fig. 11-2:

LEDs at KCU02

LED

Color / status

Significance

Measures

H49

Safety

Green

Safety technology signals without

error

None

Red

Safety technology signals with error
(Error is saved until the device is

switched off.)

Check safety technology wiring for short circuit.

H52.1

E-Stop

Off

E-Stop not activated

None

Red

E-Stop active (/E_Stop)

Deactivate E-Stop, if necessary (see connection

point X50)

H52.2

Power Supply

Green

Supply unit without error, regular

status

None

Red

Supply unit signals error (/Bb_V)

Check power supply, see also "F2086 Error

supply module"

H52.3

Warning

Green

Supply unit without warning

(/Warn), regular status

None

Red

Supply unit signals warning

Check supply unit, see also "E2086 Prewarning

supply module overload"

H52.4

DC Bus In

Off

DC bus voltage (L+; L-) too low

Switch power on at supply unit

Module bus not connected (if H54

green)

Connect module bus (connection point X1)

Green

DC bus voltage (L+; L-) without

error (Ud), regular status

None

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

343/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands