Bosch Rexroth IndraDrive Mi KCU02 Project Planning Manual Download Page 34

Page: 34 / 422

1.3.5

KCU02 drive connection box

KCU02.2 type code

Short type designation 1 2 3 4 5 6 7 8 9

1
0 1 2 3 4 5 6 7 8 9

2
0 1 2 3 4 5 6 7 8 9

3
0 1 2 3 4 5 6 7 8 9

4
0

Example:

K C U 0 2 . 2 N - E T - E T * - 0 2 5 - N N - N - N N - N W

①

② ③④ ⑤

⑥

⑦

⑧ ⑨ ⑩ ⑪

①

Product:
KCU = KCU

②

Series:
02 = 2

③

Design:
2 = 2

④

Configuration option:
N = Fixed configuration

⑤

Master communication (input):
ET = Multi-Ethernet

⑥

Master communication (output):
ET* = Multi-Ethernet

⑦

DC fuse:
025 = Nominal current: 25 A

⑧

Interface:
NN = None

⑨

Control panel:
N = Without

⑩

Other design:
NN = None

⑪

Firmware:
NW = Without firmware

Tab. 1-11:

Type code KCU02.2

KCU02.2 vs. KCU02.1

KCU02.2 is fully downward compatible with version KCU02.1 and completely

replaces this type.

20/407

System presentation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Summary of Contents for Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands

Bosch Rexroth IndraDrive Mi KCU02, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive Mi KCU02

Reviews:

Related manuals for Rexroth IndraDrive Mi KCU02

Brands by name

Popular brands