Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 249

Page: 249 / 344

See following note regarding output current reduction

5) 6) 7) 8)

See parameter description "P-0-0556, Config word of axis con‐

troller", load-dependent reduction of switching frequency fs

Tab. 7-49:

HCS - Power section data - inverter

Guide value "Rise of voltage at output"
Observe that the voltage load at the motor is almost independent

of the power section used.
Especially when using standard motors, make sure that they com‐

ply with the occurring voltage load.

Reduced output current at motor standstill
Depending on the electric output frequency, the output current is

reduced for thermal protection of the power section.
The output current is reduced, when the electric output frequency

has fallen below the threshold to detect motor standstill.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

247/341

Rexroth IndraDrive CsDrive Systems with HCS01

Technical data of the components

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands