Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 134

Page: 134 / 344

X4, motor encoder connection

View

Identifica‐

tion

Function

Motor encoder connection

D-Sub, 15-pin, female

Unit

min.

max.

Connection cable
Stranded wire

0.25

0.5

Type of encoder evaluation

Tab. 6-4:

Function, properties

Technical data

chapter 7.1.1 "EC - standard encoder evaluation" on page 181

Supported encoder systems

Encoder systems with a supply voltage of 5 and 12 V:
●

MSM motor encoder

●

MS2N motor encoder

●

MSK motor encoder

●

sin-cos encoder; HIPERFACE®

●

sin-cos encoder; EnDat 2.1; EnDat 2.2

●

sin-cos encoder; with reference track

●

5V TTL square-wave encoder; with reference track

●

SSI

●

Combined encoder for SSI (combination of SSI and 1V

sin-cos encod‐

er)

●

Resolver (resolvers are not supported if optional "Safe Motion" safety

technology is also in use)

●

Hall sensor box SHL02.1

●

Digital Hall sensor in conjunction with Hall sensor adapter box SHL03.1

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

132/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands