Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 123

Page: 123 / 344

Mounting and installation

6.1

Mounting HCS01 Devices in the Control Cabinet

Mounting surface in control cabinet

Left-hand mounting

Back-side mounting (standard mounting)

Right-hand mounting

Fig. 6-1:

Options for Mounting

Notes on Mounting

●

Observe the minimum distances to be complied with for mounting (see

technical data or dimensional drawings).
The specified horizontal minimum distance refers to the distance to

neighboring devices or equipment installed in the control cabinet (such

as cable ducts) and not to the distance to the control cabinet wall.

●

The back-side mounting (back of device directly mounted to mounting

surface in control cabinet) is the standard and should be used, if possi‐

ble.

●

The left-hand or right-hand mounting (left or right side of device directly

mounted to mounting surface in control cabinet) can be used, if the

mounting clearance between control cabinet wall and control cabinet

front is not sufficient for back-side mounting.
NOTICE! Risk of damage by high temperatures! At the back of the

HCS01 devices, there are braking resistors which can become very hot

during operation. When arranging the devices in the control cabinet,

make sure there aren't any heat-sensitive materials close to the braking

resistors.
In the case of left-hand or right-hand mounting, you must not pile the de‐

vices. Each device must have immediate contact to the control cabinet

wall.

●

Tightening torque of the mounting screws: 6 Nm

●

On the sides of the devices, there are adhesive labels with notes on

safety. The supplied accessory

HAS09

additionally contains these adhe‐

sive labels. If the adhesive labels at the devices are no longer visible af‐

ter mounting, place the adhesive labels from the

HAS09

accessory

clearly visibly at the device or in the immediate vicinity of the device.

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

121/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands