Bosch Rexroth IndraControl XFE01.1-SY-01 Operating Instructions Manual Download

Page: 7 / 52

1 About this documentation

Editions of this documentation

Edition

Release

Date

Note

Edition 01

2016-10 First edition

Edition 02

2017-06 Chapter "Safety standards" revised, new chapter "Ordering data",

standards and warning instructions modified for UL

Edition 03

2019-05 References supplemented

Tab. 1-1: Change Record

1.1 Overview on target groups and product phases

In the following illustration, the framed activities, product phases and target

groups refer to the present documentation.
Example: In the product phase "Mounting (assembly/installation)", the

"mechanic/electrician" can execute the activity "unpack, mount and install" using

this documentation.

Presales Aftersales

Selection

Mounting

(assembly/installation)

Engineering

Commissioning Operation

Decommissioning

Product

phases

Target

groups

Activities

Design engineer

Programmer
Technologist

Process

specialist

Select

Prepare

Design

Construct

Mechanic/

electrician

Unpack

Mount

Install

Programmer

Commissioning engineer

Parameterize

Program

Configure

Simulate

Technologist

Process specialist

Optimize

Test

Machine

operator

Maintenance

technician

Service

Operate

Maintain
Remove

faults

Create

the NC program

Mechanic/

electrician

Disposal company

Dismount

Dispose

Fig. 1-1: Assigning the present documentation to the target groups, product phases and ac-

tivities of the target group

IndraControl XFE01.1-SY-01 Safety Ex-

tension Module

1/45

About this documentation

R911376654_Edition 03 Bosch Rexroth AG

Summary of Contents for Rexroth IndraControl XFE01.1-SY-01





















































Search results

Summary of Contents for Rexroth IndraControl XFE01.1-SY-01

Reviews:

Related manuals for Rexroth IndraControl XFE01.1-SY-01

Brands by name

Popular brands

Bosch Rexroth IndraControl XFE01.1-SY-01, Operating Instructions Manual

Search results

Summary of Contents for Rexroth IndraControl XFE01.1-SY-01

Reviews:

Related manuals for Rexroth IndraControl XFE01.1-SY-01

Brands by name

Popular brands