Bosch Rexroth IndraControl S67 Series Application Description Download Page 49

Page: 49 / 142

Web-Based Management (WBM)

8.1

General information

The Web-Based Management (WBM) serves to configure the Sercos field

bus coupler. An Internet browser is needed in order to use the WBM. Enter

the IP address of the field bus coupler into the address bar (e.g., http://

192.168.1.1). For information on how to assign an IP address to the field bus

coupler, please refer to

chapter 7.3 "Assigning IP Address" on page 44

A password prompt is displayed when connecting for the first time. The user

names and passwords are explained in

chapter 8.2 "User Administration" on

page 47

Fig. 8-1:

8.2

User Administration

Access to the web-based management is password protected. Upon delivery,

the following users and access authorizations are defined:

User name

Password

Access

admin

rexroth

Full access

user

Limited access

guest

Limited access

Tab. 8-1:

User Management

The passwords can be changed on the "Users" page.

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P
Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

Bosch Rexroth AG

47/139

Web-Based Management (WBM)

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Bosch Rexroth IndraControl S67 Series, Application Description, Page: 49 / 142

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews: