Bosch Rexroth IndraControl S67 Series Application Description Download Page 107

Page: 107 / 142

Diagnostics

10.1

LED Signaling

The field bus coupler has various LEDs for local diagnostics that display its

operating state and that of the S-BUS.

10.2

Ethernet Status Messages

The following table lists the Ethernet status messages that are signaled by

the LEDs (21) on the field bus coupler. Causes and remedies/information are

specified additionally.

SBM

MS 1

1 FB 2

FB 2

ACT/LNK

sercos

S3-BK-DI8

Fig. 10-1:

LEDs to display Ethernet status messages

LED

Color/status

Cause

Remedy/information

Off

No power supply ap‐

plied at the field bus

coupler

Check the power supply

for the field coupler.
Check the cable for

damage

Green

The field bus coupler

operates correctly

–

Flashing green The Ethernet interface

of the field bus coupler

is not yet completely

configured

Configure the field bus

coupler (e.g. assigning

an IP address)

Flashing red

The Ethernet interface

could not be configured

The malfunction can be

recovered. Contact the

Bosch Rexroth Service

ACT/LNK 1

Off

Field bus coupler has

no connection to the

physical network

Check the cable con‐

nection of the Ethernet

connection FB1

Green

Connection to physical

network present

–

Flashing green Data exchanged via

Ethernet

–

ACT/LNK 2

Off

Field bus coupler has

no connection to the

physical network

Check the cable con‐

nection of the Ethernet

connection FB2

Green

Connection to physical

network present

–

Flashing green Data exchanged via

Ethernet

–

Tab. 10-1:

Ethernet status messages

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P
Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

Bosch Rexroth AG

105/139

Diagnostics

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl S67 Series, Application Description

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands