Bosch Rexroth IndraControl S67 Series Application Description Download Page 100

Page: 100 / 142

Status

code

Name

Description

0x1800

Timing configura‐

tion order error

Configuration order for the timing parameter is in‐

correct (e.g., timing configuration of the control is

incomplete)

0x8100

Communication

Critical errors with synchronous data exchange

0x8210

System deviation

high

Synchronization error of the S-BUS with the field

bus

0xB020

Local bus commu‐

nication error

Communication error on the S-BUS (e.g., inter‐

ruption of the S-BUS)

0xB030

Local bus configu‐

ration error

Configuration error on the S-BUS (e.g., configura‐

tion of the I/O modules was changed on the S-

BUS)

Tab. 9-30:

Supported Sercos status codes for I/O errors (C1D)

Example for diagnostic class warning (C2D)
In case of a wire break at channel 5 of module S67-DO8-M8 (slot 3), the fol‐

lowing diagnostic information is provided:

IDN/S-0-0095 "Diagnosis message"

ASCII text

= "Open load"

IDN/S-0-0390 "Diagnostic number"

Hexadecimal value (32-bit)

= 0xC10E2350

Bit 31:30 "Interpretation of the bits 29:0"

= 0b11 (standard diagnostics)

Bit 29:24 "Device profile"

= 0x01 (FSP_IO)

Bit 19:16 "Diagnostic class"

= 0x0E (warning (C2D))

Bit 15:0 "Status code"

= 0x2350 (interruption)

IDN/S-0-1500.00.32

Hexadecimal value (64-bit)

= 0x0E235005DE030005

Bit 63 "Interpretation of the status code"

= 0 (status code of the FSP_IO)

Bit 59:56 "Diagnostic class"

= 0x0E (warning (C2D))

Bit 55:40 "Status code"

= 0x2350 (interruption)

Bit 39:24 "I/O function group"

= 0x05DE (S-0-1502)

Bit 23:16 "slot number"

= 3

Bit 15:8 "slave index"

= 0

Bit 7:0 "channel number"

= 5

9.5

IP Communication

The Sercos field bus coupler S67-S3-BK-DI8-M8 provides various services

via the NRT channel using IP-based protocols:
●

Web-based management (TCP/IP, HTTP, WBM)

●

Automatic IP address assignment (BootP, DHCP)

The web-based management (WBM) allows the user to carry out the basic

configuration of the coupler. In addition, the current status of the coupler is

Bosch Rexroth AG

DOK-CONTRL-S67S3BKDI8*-AP03-EN-P

Rexroth IndraControl S67 Sercos Coupler 8 Digital Inputs (M8)

98/139

Sercos

Summary of Contents for Rexroth IndraControl S67 Series















































































































































Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands

Bosch Rexroth IndraControl S67 Series, Application Description

Search results

Summary of Contents for Rexroth IndraControl S67 Series

Reviews:

Related manuals for Rexroth IndraControl S67 Series

Brands by name

Popular brands