Bosch Rexroth IndraControl S20 Page 52 Manual Download

Page: 52 / 88

Code +

AddValue

Error cause

LED

Description, effect

Solution

0x2382

+ 0x02F2

There is at least still one output

with a parameterized switch-off

delay in the switch-off process

flash‐

ing

The module is retained in the

safe state.

Wait for the completion of the

switch-off process and send param‐

eter data again to the module.

0x6320

+ 0x023X

The parameterization of two rela‐

ted outputs does not correspond

to the dual-channel setting

Correct the value and send the pa‐

rameter data again to the module.

0x6320

+ 0x02EX

The parameterized switch-off de‐

lay time is outside the permitted

value range

Correct the value and send the pa‐

rameter data again to the module.

0x6320

+ 0x029X

For outputs parameterized as

dual-channel, different settings

than for the switch-off delay were

assigned

Correct the value and send the pa‐

rameter data again to the module.

0x6320

+ 0x03F2

Calculated and received check‐

sum of the parameter data does

not match

Check checksum and send param‐

eter data again to the module.

0x6320

+ 0x03FB

Device ID is incorrect or wrong

module is used.

Check that the correct module is

used. If the error cannot be elimina‐

ted, contact Bosch Rexroth.

Tab. 9-11:

Parameterization errors (cannot be acknowledged)

9.2.5

General errors

Code

Error cause

LED

Description, effect

Acknowledgement, remedy

0x4210 Critical module temper‐

ature

The module temperature reached a criti‐

cal value. The switch-off is imminent. If

the temperature increases more, the

module goes into the safe state using the

device firmware.

Check the ambient conditions and

switching frequency and modify

them if required.
This diagnostic message can be

acknowledged. The acknowledge‐

ment deletes the diagnostic mes‐

sage.

0xA012 Possible error causes:

●

Application is not

ready on the

module

●

Hardware error

●

TUNID (DIP

switch) was

changed at run‐

time

FS on The communication to a safe parent con‐

trol is locked. The module goes into the

safe state.

This diagnostic message cannot be

acknowledged. Execute power-up.
If the error message is output

again, the module is defective and

has to be replaced.

Tab. 9-12:

General errors

9.3

CSos errors

The following errors can occur additionally:
●

For errors of the CSos system, refer to

chapter 13 "CSos parameters

and device parameters" on page 65

Bosch Rexroth AG

DOK-CONTRL-S20*SSDO*8*-AP02-EN-P

50/85

IndraControl S20 Module With Safe Digital Outputs S20-SSDO-8/3

Errors: Reporting and troubleshooting

Summary of Contents for Rexroth IndraControl S20

























































































Search results

Summary of Contents for Rexroth IndraControl S20

Reviews:

Related manuals for Rexroth IndraControl S20

Brands by name

Popular brands

Bosch Rexroth IndraControl S20, Manual

Search results

Summary of Contents for Rexroth IndraControl S20

Reviews:

Related manuals for Rexroth IndraControl S20

Brands by name

Popular brands