Bosch Rexroth IndraControl L45 Project Planning Manual Download Page 10

Page: 10 / 84

The IndraControl L45/L65/L85 may only be operated under the assembly and

installation conditions, in the position of application and under the ambient con‐

ditions (temperature, degree of protection, humidity, EMC, etc.) specified in this

documentation.

The emission (EMC) of this device is tested according to EN

61000-6-4 and complys with limit class A according to IEC/CISPR

22. Therefore the device is suitable for use in industrial environ‐

ments. For use in residential and commercial areas additional noise

suppression measures may be required, if applicable.

2.2

Inappropriate Use

Any use of IndraControl L45/L65/L85 in applications other than those specified

above or under operating conditions other than those described in the docu‐

mentation and the technical specifications is considered to be "non-intended

use".
IndraControl L45/L65/L85 must not be used if
●

it is exposed to operating conditions that do not fulfill the ambient condi‐

tions specified. For instance, operation under water, in case of extreme

variations of temperature or in extreme maximum temperatures is not al‐

lowed.

●

they are used in household devices or devices belonging to categories 1

to 7 and 10 specified in Appendix IA of the Directive 2002/96/EC

("WEEE").

Bosch Rexroth AG

DOK-CONTRL-ICL45L65L85-PR01-EN-P

Rexroth IndraControl L45/L65/L85 Control

8/81

Important Instructions on Use

Summary of Contents for Rexroth IndraControl L45





















































































Search results

Summary of Contents for Rexroth IndraControl L45

Reviews:

Related manuals for Rexroth IndraControl L45

Brands by name

Popular brands

Bosch Rexroth IndraControl L45, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraControl L45

Reviews:

Related manuals for Rexroth IndraControl L45

Brands by name

Popular brands