Bosch Rexroth H-4WEH...XE Series Operating Instructions Manual Download | Manualshive

Page: 42 / 52

background image

42/52

Maintenance and repair

Bosch Rexroth AG

, H-4WEH...XE..., RE 24751-XE-B/04.16

10.6 Spare parts

Table 16: Replacement nBR seal kit for the valve connection surface

Valve type

Material number

H-4WEH10...

R961001132

H-4WEH16...

R961001255

H-4WEH25...

R961001257

H-4WEH32...

R961001259

Table 17: Replacement FKM seal kit for the valve connection surface

Valve type

Material number

H-4WEH10...V...

R961001131

H-4WEH16...V...

R961001256

H-4WEH25...V...

R961001258

H-4WEH32...V...

R961001260

Ensure suitability of the sealing materials for the hydraulic fluid used! See

"Data sheet 24751-XE"

.

Table 18: Spare part seal kit for the terminal box

Spare part

Material number

Seal kit terminal box
contains:
1 complete cable and line entry
1 blind plug for the O-ring
4 M4 hexagon socket head cap screws for the terminal box
4 spring washers for the terminal box
1 flat seal

R961009879

For a valve with two valve solenoids, two seal kits are required.

In case of questions regarding spare parts, please contact the competent
Rexroth service.
Bosch Rexroth AG
Service Hydraulics
Bürgermeister-Dr.-Nebel-Str. 8
97816 Lohr am Main
Phone: +49 (0) 9352 - 40 50 60
[email protected]

For the addresses of our sales and service network, please refer to:

www.boschrexroth.com/adressen

nBR seal kit for the valve

connection surface

FKM seal kit for the valve

connection surface

Seal kit terminal box

«
...
40
41
42
43
44
...
»

Summary of Contents for Rexroth H-4WEH...XE Series





















































Reviews:

No comments

Related manuals for Rexroth H-4WEH...XE Series

Brand: Faulhaber Pages: 66

Brand: Hanna Instruments Pages: 54

Brand: Hanna Instruments Pages: 2

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Brand: U-Prox Pages: 3

Brand: U.S. Divers Pages: 22

Brand: Paradox Pages: 3

Brand: SYR Pages: 2

Brand: One for All Pages: 15

Brand: LCT Pages: 5

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Precision Pages: 8

TRAP-SHUFFLE Game Simulator

Brand: RF SOLUTIONS Pages: 2

Brand: Mosa Pages: 28

Brand: M-system Pages: 7

Brand: Texecom Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands