Bosch rexroth CytroForce-M Operating Manual Download Page 65

Page: 65 / 85

65 / 85

Servo-hydraulic actuator

Replacement of components

Bosch Rexroth AG

RE62270-B, 01.21

10.4

Repair

WARNING

Improper repair!

−

For repairs the servo-hydraulic actuator may only be

disassembled to the extent described in these oper-

ating instructions.

−

Defective parts may only be replaced by new, inter-

changeable, tested components in original equipment

quality.

−

Only use genuine spare parts from Bosch Rexroth for

repairing the servo-hydraulic actuator and the drive

controller.

−

Repairs may only be performed by authorized, skilled

and instructed staff.

WARNING

Danger due to pressurized servo-hydraulic actuator! Risk

of injury! Severe injury when working on systems that

have not been shut down! Damage to property! Even

after the servo-hydraulic actuator was disconnected from

the electrical power supply, the system is still under

pressure and is permanently prestressed!

−

Observe the specifications of the system manufac-

turer and the system end-user.

−

Do not disconnect line connections, ports or compo-

nents as long as the servo-hydraulic actuator is pres-

surized.

−

The hydraulic circuit may only be opened by specifi-

cally trained personnel.

Bosch Rexroth has an extensive service offer regarding repairs. Should you

have any queries, please contact Bosch Rexroth Service, see

⮫

Chapter 16.1

“Service and support” on page 77

10.5

Spare parts

Regarding spare parts, please contact Bosch Rexroth Service for clarification,

see

⮫

Chapter 16.1 “Service and support” on page 77. In addition, observe

the safety instructions in these operating instructions when working on the

servo-hydraulic actuator and the drive controller.

10.6

Replacement of components

For the replacement of defective components and in case of questions or when

in doubt, please contact Bosch Rexroth Service, see

⮫

Chapter 16.1 “Service

and support” on page 77.

Summary of Contents for rexroth CytroForce-M






















































































Search results

Summary of Contents for rexroth CytroForce-M

Reviews:

Related manuals for rexroth CytroForce-M

Brands by name

Popular brands

Bosch rexroth CytroForce-M, Operating Manual

Search results

Summary of Contents for rexroth CytroForce-M

Reviews:

Related manuals for rexroth CytroForce-M

Brands by name

Popular brands