English |
13
Tightening screws and nuts of the maximum permitted size:
a
h
=
9
m/s
2
, K =
1.5
m/s
2
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Charging the battery
u
Use only the chargers listed in the technical data.
Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note:
The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Do not continue to press the On/Off switch after the
power tool has automatically switched off.
The battery
can be damaged.
Removing the battery (see figure A)
To remove the battery
(6)
, press the release button
(5)
and
pull the battery downwards out of the power tool.
Do not
use force to do this.
Changing the tool (see figure B)
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
Inserting
Pull the locking sleeve
(2)
forward, guide the application tool
(1)
into the tool holder up to the stop and release the locking
sleeve
(2)
to lock the application tool.
Use only screwdriver bits with ball catch
(13)
(DIN 3126-
E6.3). Other screwdriver bits
(12)
can be inserted using a
universal bit holder with ball catch
(11)
.
Removing the application tool
– Pull the locking sleeve
(2)
forward and remove the applic-
ation tool.
Operation
Method of Operation
The tool holder
(1)
(with the application tool) is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Screwing in
and
tightening
(impact mechanism in action).
The impact mechanism is activated as soon as the screwed
connection runs tight and load is therefore put on the motor.
The impact mechanism then converts the power of the mo-
tor to steady rotary impacts. When loosening screws or nuts,
the process is reversed.
Starting Operation
Inserting the battery
Note:
The use of batteries unsuitable for your power tool can
lead to malfunctions or damage to the power tool.
Set the rotational direction switch
(7)
to the middle position
to avoid unintentionally switching it on. Insert the charged
battery
(6)
into the handle until you feel it engage and it is
flush with the handle.
Set the rotational direction (see figure C)
The rotational direction switch
(7)
is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch
(8)
is being pressed.
Right rotation:
To drive in screws and tighten nuts, press
the rotational direction switch
(7)
through to the left stop.
Left Rotation:
To loosen and unscrew screws and nuts,
press the rotational direction switch
(7)
through to the right
stop.
Switching on/off
To
start
the power tool, press and hold the on/off switch
(8)
.
The LED
(3)
lights up when the on/off switch
(8)
is lightly or
fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To
switch off
the power tool, release the on/off switch
(8)
.
Bosch Power Tools
1 609 92A 4JH | (24.11.2020)
