manualshive.com logo in svg

Bosch PRAESENSA PRA-AD604, Configuration Manual, Page: 79 / 164

Share
Download
Bosch PRAESENSA PRA-AD604 Configuration Manual Download Page 79

PRAESENSA

Configure the system | en

79

Bosch Security Systems B.V.

Configuration manual

2020-09 | V1.20 | PRAESENSA 1.20

5.5.3

BGM routing

At the BGM routing page, background music (BGM) routing can be defined. A BGM routing
refers to an audio input in the system. Optionally, default zones and or default zone groups
can be connected to the routing. When the system is switched on, then the specified BGM is
routed to the connected zones and zone groups.

BGM routing configuration page

1.

Below

 the Zone definitions page, 

click

 BGM routing:

–

A screen appears listed the following items:

2.

Select

, 

enabl

e or 

disable

 each of the following items:

Item

Value

Description

Name

Selection

Shows

 the name of the BGM routing

(dropdown list selection). See Add BGM
routing topic in this section.

Type

Selection

Selection

 between zones and zone groups as

available routing.

Zones / Zone groups

Selection

The left box area 

shows

 the available zones

and zone groups. Zones (groups) are created
in 

Zone options, page 75 and Zone grouping,

page 77

> and <

Buttons

Using

 the > and < buttons, selected zones

and zone groups can be added to, or removed
from, Routing (the right area box).

Audio input

Selection

Select

 the Audio input that provides the

background music. 

Notice

 that the inputs 9

up to 16 are 

secured

 (Dante/OMNEO

channels) to the amplifier. The same Audio
input may not be assigned to different BGM
routing. Each BGM routing must have a

unique

 audio input.

Limit routing

Enable / Disable

Enable: 

The center box area shows the zones

and zone groups that are allowed to receive
the BGM routing. This center box area is not
visible if the Limit routing checkbox is
disabled. 

Using

 the > and < buttons, selected

zones and zone groups (left area box) can be
added to, or removed from Limit Routing (the
middle area box). 

See

 also the Limit routing

topic in this chapter.

Routing

Selection

The right box area 

shows

 the zones and zone

groups that are assigned to the selected BGM
routing at system start‑up. 

Using

 the > and <

buttons, selected zones and zone groups (the
left or middle area box) can be added to, or
removed from Routing (right area box).

Summary of Contents for PRAESENSA PRA-AD604





































































































































































Reviews:

No comments