en
Operating the appliance
8
1
Operating the appliance
Operating the appliance
Notes
■
Only use the accessories specified.Do not line the
cooktop (e.g. with aluminium foil).
■
The burner and ignition plug must be clean and dry.
■
Only light the hotplates if the pan supports and all
burner parts are correctly fitted.
■
When one burner is ignited, an ignition spark will
also be generated at all the other burners.
■
Do not touch the ignition plug while the gas
appliance is being lit.
■
It is important to keep the appliance clean. If the
ignition plugs are dirty, this may cause ignition
problems. Clean the ignition plugs regularly with a
small, non-metallic brush. Take care to prevent the
ignition plugs from suffering any heavy knocks.
■
When the gas cooktop is switched on, the
electronics open up the gas supply, which produces
a short sound. This is normal.
Switching on automatically
Your gas hob comes with ignition plugs for electrical
ignition.
1.
Place suitable cookware on the required burner.
2.
Press the corresponding control knob in and turn it
anti-clockwise to the required heat setting.The burner
will ignite automatically.
3.
Keep the control knob pressed in for a few seconds
after ignition.
:
Warning – Risk of deflagration!
If the burner does not ignite after 10
seconds, switch off
the control knob and open the door or window in the
room. Wait at least 1
minute before trying to ignite the
burner again.
Switching on manually
1.
Press the chosen burner control knob and turn it
anticlockwise to the required setting.
2.
Use any type of lighter or flame (cigarette lighter,
matches, etc.) and bring it close to the burner.
Thermoelectric flame monitoring
For your safety, the hob is fitted with thermoelectric
flame monitoring. This prevents the flow of gas if the
burner accidentally goes out while it is in use (e.g. due
to draughts).
If the burner accidentally goes out while it is in use, turn
the control knob to position 0
and wait at least one
minute before you ignite the burner again.
Switching off
Turn the control knob you require clockwise to position
0
until the control knob locks in place.
D
Cleaning
Cleaning
:
Warning – Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
:
Warning – Risk of electric shock!
Do not use high pressure washers or steam cleaners to
clean the appliance.
Cleaning
Clean the appliance after every use once it has cooled
down. Remove spills immediately. Burnt in residues and
milk spills may be difficult to remove.
Assemble the burner parts and pan supports after
cleaning and drying them. Make sure all burner parts
are properly fitted. Burner ring and burner cover must
lock in place and lie evenly flat.
Part/surface
Recommended cleaning method
Stainless steel
surfaces
Clean with a soft cloth and some
soapy water; polish dry with a soft
cloth. Do not use too much water to
avoid water entering the appliance.
Caution!
Damage to the seal
Do not clean the gap around the
stainless steel surface with sharp
objects. Only clean with a soft
brush.
To remove stubborn residues
including discoluration and dried
milk spills because of the heat, you
can order a stainless-steel cleaner
(order number 464524) from your
specialist retailer or our after-sales
service.
Pan support
Carefully take off pan supports for
cleaning. Soak in soapy water.
Clean with a brush and some
detergent.
Be careful when cleaning around
the rubber rests to ensure they do
not come loose.
Rinse with clear water. Carefully dry
pan support before assembly.
Do not clean in a dishwasher!
Control knobs Clean with a soft, moist cloth and
some soapy water; do not use too
much water.
Caution!
Damage to the appliance
Do not pull off the control knobs to
clean them.
Summary of Contents for PPH6S6F20I
Page 2: ...2 ...
