English |
17
Bosch Power Tools
2 609 006 340 | (23.7.12)
Mounting/Replacing the Application Tool/Accessory
(see figures A–C)
f
Check the tight seating of the application tool/acces-
sory.
Incorrect or not securely fastened application tools/
accessories can come loose during operation and pose a
hazard.
Inserting the Tool Retainer (see figure D)
When the SDS lever
1
was opened too far, the tool retainer
14
can fall out of the gear head.
Insert the tool retainer
14
into the gear head in such a manner
that its flat side fits into the opening. Turn the SDS lever
1
clockwise.
Mounting the Depth Stop
The depth stop
12
can be used when working with segment
saw blades, Riff-segment saw blades and segment blades.
If required, remove an already mounted application tool/
accessory.
Slide the depth stop
12
over and beyond the tool holder
8
to
the stop onto the gear head of the power tool with the labelled
side facing upward.
The depth stop is intended for the following cutting depths:
– With segment saw blades ACZ 85 .. with a diameter of
85 mm: 8 mm, 10 mm, 12 mm and 14 mm cutting depths
(see indication on the depth stop in large font and not in
brackets).
– With segment saw blades ACZ 100 .. with a diameter of
100 mm: 14 mm, 16 mm, 18 mm and 20 mm cutting
depths (see indication on the depth stop in smaller font
and brackets).
Mount the fitting segment saw blade for the desired cutting
depth. Turn the depth stop
12
in such a manner that the de-
sired cutting depth is above the section of the saw blade, with
which the cut is to be made.
For all other cutting depths and when working with other appli-
cation tools, remove the depth stop
12
. For this, remove the
application tool and pull the depth stop from the gear head.
Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate
10
is fitted with Velcro backing for quick
and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet
11
, free the Velcro back-
ing of the sanding plate
10
from any debris by tapping against
it in order to enable optimum adhesion.
Position the sanding sheet
11
flush alongside one edge of the
sanding plate
10
, then lay the sanding sheet onto the sanding
plate and press firmly.
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
To remove the sanding sheet
11
, grasp it at one of the tips and
pull it off from the sanding plate
10
.
You can use all sanding sheets, fleece pads/polishing cloth
pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
n
If required, remove an already mounted application
tool/accessory. For this, push SDS lever
1
out of the lock-
ing position and sidewards.
To release the tool retainer
14
, turn the SDS le-
ver approx. 3 turns in anticlockwise direction.
Note:
Do not turn the SDS lever
1
further than necessary,
otherwise the tool retainer
14
can fall out of the gear head
(see “Inserting the Tool Retainer”, page 17).
o
Remove the application tool/accessory.
p
Position the new application tool/accessory (e.g. plunge
cut saw blade
9
) with its opening above the tool retainer
14
. Move it on the tool holder
8
so that the recesses of the
application tool/accessory engage in the cams of the tool
holder.
To achieve a safe and low-fatigue working stance, the ap-
plication tools/accessories can be mounted on the tool
holder in any locking position. Mount the application
tool/accessory with the off-set facing downward (as
shown in the figure).
q
Turn the SDS lever
1
clockwise to lock the tool
retainer
14
and clamp the application tool/
accessory. Hand-tighten the SDS lever.
r
When the SDS lever is not positioned directly above the
locking position, turn it back in anticlockwise direction
until it is located above the locking position. In no-load,
the SDS lever can be turned back by one turn (max.).
Turn the SDS lever until it is located directly above the
locking position.
s
Press SDS lever
1
down so that it can be heard to engage
in the locking position.
Sanding disc
Material
Application
Grain size
Red quality
– All wooden materials
(e.g., hardwood, soft-
wood, chipboard, build-
ing board)
– Metal materials
For coarse-sanding, e.g. of rough, unplaned beams and
boards
coarse
40
60
For face sanding and planing small irregularities
medium
80
100
120
For finish and fine sanding of wood
fine
180
240
320
400
OBJ_BUCH-1645-002.book Page 17 Monday, July 23, 2012 8:57 AM
