Bosch PCM 8 S, Original Instructions Manual

Page: 30 / 335

30 | English
Sliding mitre saw PCM 8 S
PCM 800 S
PCM 8 ST
Hole diameter mm 30 30
A)
Tool version with base unit
Permitted workpiece dimensions (maximum/minimum)(see "Permissible workpiece dimensions", page 33)
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-
specific models.
Noise information
Noise emission values determined according to EN
62841-3-9 .
Typically, the A-weighted noise level of the power tool is:
Sound pressure level
94 dB(A); sound power level
102 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
u
Avoid starting the power tool unintentionally. The
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
work on the power tool.
Items included
See the list of items included at the start of
the operating manual.
Check to ensure that all the parts listed below have been
supplied before using the power tool for the first time:
– Sliding mitre saw with mounted saw blade
– Dust bag
(23)
– Stationary saw table extension (17) (2 x),
fastening screws (16) (2 x)
– Flexible saw table extension (48) (2 x)
– Screw clamp (19)
– Hex key (38)
– Tilt protector (30) with fastening screws (42)
Additional components on the PCM 8 ST (tool version
with base unit)
Base unit
– Leg profiles
(F) , (C) (4 x each)
– Connecting profiles (E) , (D) (2 x each)
– Head profiles (A) , (B) (2 x each)
– Shim (i) (2 x)
Fastening set
– Base unit carriage bolts
(g) (26 x)
– Flange nuts (h) (30 x)
– Power tool fastening screws (j) (4 x)
– Washers (k) (4 x)
Note: Check the power tool for possible damage.
Before continuing to use the power tool, carefully check that
all protective devices or slightly damaged parts are working
perfectly and according to specifications. Check that the
moving parts are working perfectly and without jamming;
check whether any parts are damaged. All parts must be fit-
ted correctly and all the conditions necessary to ensure
smooth operation must be met.
If the protective devices or any parts become damaged, you
must have them repaired or replaced by an authorised ser-
vice centre immediately.
Extra tools required (not included in the delivery):
– Ring spanner or open-ended spanner (12 mm) for assem-
bling the base unit
Fitting individual components
– For ease of assembly when fitting the tool elements that
are provided, be aware that the power tool is supplied in
the transport position.
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material from the power tool and the
accessories provided.
Mounting the tilt protector (see figure A)
Before the power tool is used for the first time, the tilt pro-
tector
(30) must be mounted.
– Turn the power tool over and place it carefully on the pro-
tective guard (4) and the saw table (8) .
– Push the tilt protector (30) into the corresponding holes
in the base plate until the threaded holes of the tilt pro-
tector and base plate align.
1 609 92A 4DT | (06.12.2018) Bosch Power Tools