Bosch OptiFlow Professional GWH12 1 CTD E23 Installation Manual Download Page 3

6 720 810 559 (2016/06)

OptiFlow Professional

Key to symbols and safety instructions | 3

1

Key to symbols and safety instructions

1.1

Key to symbols

Warnings

The following keywords are defined and can be used in this 
document:

NOTICE indicates a situation that could result in damage to 
property or equipment.

CAUTION indicates a situation that could result in minor to 
medium injury.

WARNING indicates a situation that could result in severe 
injury or death.

DANGER indicates a situation that will result in severe 
injury or death.

Important information

Additional symbols

1.2

General safety instructions

If you notice dark combustion gases or sooting:
▶ Isolate the Gas supply to the heater.
▶ Notify an authorised technician.

Installation, assembly, and modifications
Installation, assembly, and modifications to the heater must

only be performed by an authorised technician.

Maintenance
▶ The water heater is required to have a service and safety 

inspection every two years.

▶ The installer is responsible for the safety and 

environmental compatibility of the installation, according 
to local regulations.

▶ The Owner/User is responsible for keeping the area around 

the water heater free from debris.

▶ Safe access to inspect and service the water heater is the 

responsibility of the property owner.

▶ Use only genuine Bosch spare parts.

Explosive and highly flammable material
▶ Do not store or use flammable material (paper, spray cans, 

solvents, paints, etc) near the heater.

Combustion air and surrounding air
▶ The combustion air and surrounding air must be free from 

corrosive substances.

▶ Do not spray aerosols or use chemicals around the heater 

unless heater is disconnected from the power supply.

Risk of damage due to operator error
User error can result in injury and damage to property.

▶ Ensure that children never play with or operate this 

appliance.

▶ Ensure that only personnel who can operate this appliance 

correctly have access to it.

▶ Refer to the operating and user instructions before 

adjusting the water heater.

To be installed and serviced only by an authorised person
The “authorised installing person” is responsible for:

Correct installation and commissioning of this appliance.

Ensuring the appliance performs to the specifications 
stated on the rating label.

Demonstrating the operation of the appliance to the 
customer before leaving.

Handing these instructions to customer.

THIS APPLIANCE IS NOT SUITABLE FOR POOL OR SPA POOL 
APPLICATIONS.
NOT SUITABLE FOR COMMERCIAL BOOSTING OF A WARM 
WATER RECIRCULATION SYSTEM"

Regulations
All local by-laws and regulations pertaining to installation and 
use of gas appliances must be observed.

This appliance must be installed in accordance with the 
manufacturers installation instructions, AS/NZS5601, AS/
NZS3500, and all Local Building & Gas fitting regulations.

Warnings in this document are identified by a 
warning triangle printed against a grey 
background.
Keywords at the start of a warning indicate 
the type and seriousness of the ensuing risk 
if measures to prevent the risk are not taken.

This symbol indicates important information 
where there is no risk to people or property.

Symbol Explanation

Step in an action sequence

 

Cross-reference to another part of the document

List  entry

List entry (second level)

Table 1

Summary of Contents for OptiFlow Professional GWH12 1 CTD E23

























Reviews: