Bosch GV550 TT Repair Manual Download Page 5

Page: 5 / 35

9001630797

Page 5 of 35

2.1

Signage for risk levels

Signage

Meaning

DANGER

Imminent danger which may lead to death or serious
injury if it is not avoided.

WARNING

Possible imminent danger which may lead to death or
serious injury if it is not avoided.

CAREFUL

Possible imminent danger which may lead to minor
injury or physical damage if it is not avoided.

2.2

Signage for physical damage

Signage

Meaning

WARNING

Warning about possible physical damage

2.3

General safety

instructions

►

Read the repair manual and follow the instructions contained in it.

►

Proceed systematically and follow the instructions for locating and
repairing faults.

2.3.1 All domestic appliances

Electric shock hazard due to live parts

►

Errors in repairs on electrical components can lead to electric
shock!

►

Unplug the appliance from the mains at least 60 seconds before
starting the work.

►

After the repair, ensure that a safety test is performed in
accordance with standard VDE 0701 or the country's specific
standards.

Risk of injury due to sharp edges.

►

Wear protective gloves!

►

Risk of crushing during repairs, maintenance, troubleshooting and
technical servicing due to heavy, moving parts.

►

Wear protective footwear!

►

Secure heavy components to prevent them from falling down.

►

Do not insert body parts into moving components.

Risk to the appliance's safety / operation.

►

Only use original spare parts!

Risk of damage to electrostatic sensitive components (ESD).

►

Do not touch the modules, including the connections and
conductive paths.

Summary of Contents for GV550 TT




































Search results

Summary of Contents for GV550 TT

Reviews:

Related manuals for GV550 TT

Brands by name

Popular brands

Bosch GV550 TT, Repair Manual

Search results

Summary of Contents for GV550 TT

Reviews:

Related manuals for GV550 TT

Brands by name

Popular brands