English |
15
Bosch Power Tools
1 609 92A 3B5 | (4.7.16)
21
Vacuum hose*
22
Splinter guard
23
Nose plastic sliding shoe
24
Screw
25
Scale for mitre angle
26
Locking screw for parallel guide*
27
Parallel guide with circle cutter*
28
Centring tip of the circle cutter*
29
Hex key
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Noise/Vibration Information
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Battery Charging
Use only the battery chargers listed on the accessories
page.
Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note:
The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Observe the notes for disposal.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
5
show the charging status of the battery
1
. The battery
charge-control indicator only illuminates for 5 seconds after
start-up.
When no LED lights up after switching on, then the battery is
defective and must be replaced.
Cordless Jigsaw
GST 12V-70
Article number
3 601 EA1 0..
Rated voltage
V=
12.0
Stroke rate at no load n
0
min
-1
1500–2800
Stroke
mm
18
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
mm
mm
mm
70
3
3
Bevel cuts (left/right), max.
°
45
Weight according to
EPTA-Procedure 01:2014
kg
1.5–1.7*
* depending on the battery pack being used
Battery
Permitted ambient temperature
– during charging
– during operation* and during
storage
°C
°C
0...+45
–20...+50
Recommended batteries
GBA 10,8V...
GBA 12V...
Recommended chargers
AL 11.. CV
GAL 12.. CV
* Limited performance at temperatures <0 °C
GST 12V-70
Sound emission values determined
according to EN 60745-2-11.
Typically the A-weighted noise levels of the
product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
dB(A)
dB(A)
dB
77
88
3
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745-2-11:
Cutting board: a
h
=5.5 m/s
2
, K=1.5 m/s
2
,
Cutting wooden beam: a
h
=5.0 m/s
2
, K=1.5 m/s
2
.
LED
Capacity
Continuous lighting 3 x green
2/3
Continuous lighting 2 x green
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
Flashing light 3 x green
Empty
OBJ_BUCH-2905-001.book Page 15 Monday, July 4, 2016 2:41 PM
