12
| English
1 609 92A 2N2 | (12.12.16)
Bosch Power Tools
Product Description and Specifica-
tions
While reading the operating instructions, unfold the graphics
page for the vacuum cleaner and leave it open.
Intended Use
The vacuum cleaner is intended for vacuuming and extraction
of materials that are not hazardous to one’s health and for
non-flammable liquids. It is suitable for the increased de-
mands of industrial usage, as required in trades, industry and
workshops.
According to IEC/EN 60335-2-69, vacuum cleaners of dust
category L may only be used for vacuuming and extraction of
hazardous dusts with an exposition limit value > 1 mg/m
3
.
Use the vacuum cleaner only when you fully understand and
can perform all functions without limitation, or have received
appropriate instructions.
Product Features
The numbering of the product features refers to the illustra-
tion of the vacuum cleaner on the graphics page.
1
Cable holder
2
Carrying handle
3
Vacuum lid
4
Mode selector switch
5
Socket for power tool
6
Lock
7
Hose connection piece
8
Vacuum hose
9
Container
10
Latch of the vacuum cover
11
Dust bag
12
Folded filter
13
Motor protection filter
14
Level sensors
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Noise Information
Sound emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards:
EN 60335-1, EN 60335-2-69, EN
50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Before any work on the vacuum cleaner itself, pull the
mains plug.
Replacing/Inserting the Dust Bag (see figure A)
– Unlock the latches
10
and remove the vacuum lid
3
.
– Pull off the full dust bag
11
from the connection flange to-
ward the rear. Close the opening of the dust bag by folding
down the lid. Remove the closed dust bag from the vacuum
cleaner.
– Slide the new dust bag
11
over the connection flange of the
vacuum cleaner. Make sure that the full length of the dust
bag
11
faces against the inner wall of the container
9
. Re-
attach the vacuum lid
3
.
– Lock the latches
10
.
Fold up the vacuum lid
3
and hold it. Grasp
the folded filter
12
by the fins, pull up and
remove.
All-Purpose Vacuum Cleaner
GAS 25 L SFC
Article number
0 601 979 1..
Rated power input
W
1200
Frequency
Hz
50/60
Container volume (gross)
l
25
Net volume
l
16
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Symbols and their meaning
Dust bag contents
l
9
Vacuum (turbine), max.
hPa
248
Airflow (turbine), max.
m
3
/h
220
Surface of folded filter
cm
2
4300
Weight according to EPTA-
Procedure 01:2014
kg
11.8
Protection class
/
I
Degree of protection
IP 24
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ECS
All-Purpose Vacuum Cleaner
GAS 25 L SFC
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
OBJ_BUCH-464-008.book Page 12 Monday, December 12, 2016 2:10 PM
