background image

Flexidome

XT

 | Installation Manual 

EN

 | 5 

1 Introduction 

The LTC 136x and LTC 146x series Flexidome

XT

 cameras are small, 

discreet, high-security surveillance domes containing high-performance 
¼-inch CCD cameras with integral varifocal lenses. The integrated unit is 
easily mounted to an electrical box or to a wall or ceiling. The sturdy 
construction and high impact resistant polycarbon dome protect the 
camera module from damage. The camera comes ready to use and has 
line-lock, phase adjustment, and backlight compensation controls to ensure 
the highest quality image and performance. 

Type number overview 

Type number 

LTC 136x/1

0

 

LTC 146x/11 

LTC 136x/2

0

 

LTC 146x/21 

Standard CCIR 

Monochrome 

PAL 

Color 

EIA 

Monochrome 

NTSC 

Color 

Rated supply 

voltage 

12~24 VAC, 

50Hz or 12~33 VDC 

12~24 VAC, 

60Hz or 12~33 VDC 

Lens 

LTC 1361 and LTC 1461: 2.8-6 mm F1.4-360 

LTC 1462: 2-4 mm F1.4-360; LTC 1463: 3-6 mm F1.2-360 

LTC 1464: 4-9 mm F1.4-360 

CCD type 

1/4 inch 

2 Unpacking 

Unpack the equipment carefully and handle with care. The packaging 
contains: 
• Integrated 

Flexidome

XT

 camera/housing unit 

• Mounting 

hardware 

kit 

•  Special screwdriver for tamper resistant screw 
• Adapter 

plate 

•  Lens adjustment cap 
• Installation 

manual 

Note 

If equipment appears to have been damaged during shipment, repack it in 
the original packaging and notify the shipping agent or supplier. 

Bosch Security Systems | 2005-02 | V2.0 

Summary of Contents for Flexidome XT series




















Reviews: