background image

8

After-sales service

Our after-sales service is there for you if your appliance needs 

to be repaired. We will always find the right solution in order to 

avoid unnecessary visits from a service technician.
When calling us, please give the product number (E no.) and 

the production number (FD no.) so that we can provide you with 

the correct advice. The rating plate with these numbers can be 

found inside the appliance (remove the metal mesh grease 

filter to gain access).
You can make a note of the numbers of your appliance and the 

telephone number of the after-sales service in the space below 

to save time should it be required.

Please be aware that a visit by an after-sales engineer will be 

charged if a problem turns out to be the result of operator error, 

even during the warranty period.
Please find the contact data of all countries in the enclosed 

customer service list.

To book an engineer visit and product advice

Rely on the professionalism of the manufacturer. You can 

therefore be sure that the repair is carried out by trained service 

technicians who carry original spare parts for your appliances.

Accessories for circulating-air mode

(not included in the delivery)
Basic equipment

Throw-away filter

Basic equipment

Throw-away filter

E no.

FD no.

After-sales service

O

GB

0344 8928979 

Calls from a BT landline will be charged at up to 

3 pence per minute. A call set-up fee of up to 

6 pence may apply.

IE

01450 2655 

0.03 € per minute at peak. Off peak 0.0088 € per 

minute.

1

2

3

4

1

DHZ5325

2

DHZ5326

3

DSZ5200

4

DSZ5201

Summary of Contents for DWA064W50B

















Reviews: