en
Basic operation
8
8.11 Switching off automatic mode
1
▶
Press .
a
The appliance switches to the fan setting that was
previously set.
a
The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a
Automatic mode runs for a maximum of four hours.
Note:
If automatic mode is ended using the button,
the appliance moves to the run-on position. After ap-
prox. 10 minutes, the appliance switches off automatic-
ally and moves up as far as it will go.
8.12 Sensor control
1
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on.
If the sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡
Default setting: Fan setting 3
¡
Lowest setting: Fan setting 1
¡
Highest setting: Fan setting 5
8.13 Setting the sensor control
Requirement:
The appliance is switched off.
1.
Press and hold and for approx. three seconds.
2.
Press or to change the setting.
To cancel the setting, press .
3.
To save the setting, press and hold and for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a
A signal tone sounds as soon as the selected set-
ting is saved.
8.14 Switching on the boost function
▶
Press .
a
After approx. 20 seconds, the fan automatically
switches back to the fan setting that was previously
set.
8.15 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement:
The appliance is switched off.
1.
Press and hold and for approx. three seconds.
‒
To set circulating-air mode (non-regenerable fil-
ter), press / until LED 2 lights up in the LED
display.
‒
To set circulating-air mode (non-regenerable fil-
ter), press / until LED 3 lights up in the LED
display.
‒
To convert the electronic control back to opera-
tion without the air recirculation filter, press /
until LED 1 lights up on the LED display.
2.
To save the setting, press and hold and for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
To cancel the setting, press .
a
A signal tone sounds as soon as the selected set-
ting is saved.
8.16 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡
After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡
A repeated signal tone sounds.
▶
Press .
a
The saturation indicator is reset.
8.17 Switching on the lighting
The lighting can be switched on or off independently of
the ventilation.
▶
Press .
Note:
Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
8.18 Switching off the lighting
▶
Switch off the lighting with .
8.19 Setting the brightness
▶
Press and hold down .
Note:
Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
8.20 Switching on the button tone
The button tones can be switched on.
Requirement:
The appliance is switched off.
1.
Press and hold and for approx. three seconds.
a
In the LED display, the LED for the setting that is
currently selected lights up.
2.
Press or until LED 1 lights up in the LED dis-
play.
To cancel the setting, press .
3.
To save the setting, press and hold and for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a
A signal tone sounds as soon as the selected set-
ting is saved.
8.21 Switching the button tone off
The button tones can be switched off.
Note:
Signal tones for the appliance are always
switched on and cannot be switched off.
1
Depending on the appliance specifications
Summary of Contents for DRH18LT65
Page 23: ......
