Bosch DICENTIS Page 29 Configuration Manual Download | Manualshive

Page: 29 / 134

background image

DICENTIS

Software installation | en

29

Bosch Security Systems B.V.

Configuration manual

2021.06 | V3.7 |

4

Software installation

Before the DICENTIS Conference System can be used, it needs to be configured.
Configuration of the system is done in the following order:
–

Network installation:

–

This is not part of one of our Bosch Security Systems B.V. manuals, and needs to be
defined together with your local IT department. Refer to

Hardware requirements,

page 19 and Network requirements, page 22.

–

Installation of hardware devices:

–

This is not part of this manual. Refer to the DICENTIS Hardware Installation manual.
Refer to the product related information on

www.boschsecurity.com

–

Installation of software:

Installing the DICENTIS software suite, page 29.

–

Activate the system and application software by registering the software:

removing licenses, page 30.

–

Update device (firmware) software:

Downloading software to the devices, page 29.

–

Configuration of system and application software:

Meeting application, page 37.

4.1

Installing the DICENTIS software suite

Configure network interface

i

Notice!

Before installing the DICENTIS software, make sure the server PC only has one enabled
network interface (Bluetooth is also seen as a network interface).

Download and install latest version of DICENTIS System Server Software from the Internet

1.

Go to:

https://licensing.boschsecurity.com/software

2.

Click the

Software

link (small square) to download the latest version of the software.

You can also download the latest version of the Release Notes here.

3.

Follow the on-screen instructions.

i

Notice!

During the system software installation, the application WinPcap will be installed as part of
the Network Docent package.
If you cancel the WinPcap installer, the system software installation process will fail. Simply
restart the installation process and follow the steps in the WinPcap installer.

i

Notice!

After installing/upgrading the System Server Software, make sure you download the latest
version of the software to the devices, as described in

Downloading software to the devices,

Refer to

–

Downloading software to the devices, page 29

4.2

Downloading software to the devices

–

Factory delivered DICENTIS devices are delivered with diagnostics software and must be
upgraded to the latest software version before they can be used.

«
...
27
28
29
30
31
...
»

Summary of Contents for DICENTIS







































































































































Reviews:

No comments

Related manuals for DICENTIS

Brand: ICM Controls Pages: 2

Brand: IN-COMMAND Pages: 47

Brand: Elta Pages: 142

Brand: Multi-Clean Pages: 4

Brand: Alcatel-Lucent Pages: 62

Brand: Start Shaphon Pages: 66

PNOZ m ES CC-Link

Brand: Pilz Pages: 24

Brand: Symetrix Pages: 4

FCU-EXT-APP-CONTROL

Brand: Fasel Elektronik Pages: 2

Brand: Scott Pages: 29

Brand: Jensen Pages: 17

Brand: Philips Pages: 32

Brand: Sirius XM RAdio Pages: 5

Brand: RCA Pages: 18

Brand: Nevco Pages: 14

Brand: Curtis Pages: 9

EVC80P16N7DSM00

Brand: Evco Pages: 6

Brand: Denver Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands