background image

Key to symbols and safety instructions

6 720 648 071

 

(2012/03)

4

Installation and operation

B

Have the appliance installed only by a qualified 
contractor.

B

Ensure that the hot water tank is completely full prior 
to start up. 

B

To prevent damage from excess pressure, never 
disable the safety valves. 

B

Water may escape from the safety valve when water is 
being heated.  Ensure that the safety valve is piped to 
within 6 inches of the ground in an area where 
property damage will not occur.

B

Install the unit only in a frost-free room.

B

Never store or place combustible material or liquids 
near the appliance.

B

Maintain safe clearances in accordance with local/
national regulations.

Risk of fatal injury from electric shock

B

If an aquastat is used with line voltage, it must be 
connected by a licensed electrician. The terminal 
wiring diagram must be followed.

B

Before carrying out any work, isolate all phases of the 
electrical power using the emergency shut-off switch 
or by disengaging the heating system circuit breaker. 
Secure against unintentional reconnection.

B

Do not install this device in rooms with a high 
moisture level (e.g. bathrooms, saunas).

Inspection/maintenance

B

Recommendation: sign a maintenance and inspection 
contract with a qualified heating contractor and have 
the appliance serviced annually.

B

The owner/operator is responsible for the safety and 
environmental compatibility of the system.

B

Read and follow the safety instructions in the 
"Cleaning and maintenance" chapter.

Original spare parts

Damage caused by spare parts not supplied by the 
manufacturer are excluded from our warranty.

B

Use only original  spare parts and accessories from 
the manufacturer.

Frost damage

B

When there is a risk of frost, drain the water from the 
DHW tank and the heating system's pipework. The 
system is protected from frost only if it is completely 
dry. 

Instructing the owner/operator

B

Instruct the owner/operator in the functionality and 
operation of the appliance.

B

Inform the owner/operator that they must never carry 
out any modifications or repairs.

B

Inform the owner/operator that children 
unsupervised by adults should never be in the vicinity 
of the heating system.

B

Complete the commissioning report in this document 
and hand it over to the owner/operator.

B

Give the technical documentation to the owner/
operator.

Disposal

B

Dispose of packaging in an environmentally 
responsible manner.

B

Dispose of the appliance correctly at an authorized 
disposal site.

Cleaning

B

Clean the outside of the appliance with a damp cloth.

Summary of Contents for DHW Tank QWST120 O

















Reviews: