Conettix ITS-D6682-INTL
|
Installation Guide | 3.0 Configuring and Programming the D6682
.
Bosch Security Systems, Inc. | 2/09 | F01U126778-01
9
Table 2: Netmask Address
Number of Host Bits
Netmask
1
255.255.255.254
2 255.255.255.252
3
255.255.255.248
4
255.255.255.240
5
255.255.255.224
6
255.255.255.192
7
255.255.255.128
8
255.255.255.0
9
255.255.254.0
10
255.255.252.0
11
255.255.248.0
12
255.255.240.0
13
255.255.224.0
14
255.255.192.0
15
255.255.128.0
16
255.255.0.0
17
255.254.0.0
18
255.252.0.0
19
255.248.0.0
20
255.240.0.0
21
255.224.0.0
22
255.192.0.0
23
255.128.0.0
24
255.0.0.0
25
254.0.0.0
26
252.0.0.0
27
248.0.0.0
28
240.0.0.0
29
224.0.0.0
30
192.0.0.0
31
128.0.0.0
18.
When you are prompted to change the telnet
password, press [N] for
No
(default setting).
The Setup Mode screen appears again.
Refer to
Figure 9
on page
8.
If you use a password, store it in a
secure place. If the password is lost or
forgotten you cannot connect to the
telnet program on this unit again. The
unit must be returned to the factory and
reconditioned before it can receive
another telnet session.
19.
Press
[1] [ENTER] to configure Channel 1.
Baudrate 9600 appears.
The D6682 must be set to a baud rate
of 38400.
20.
Type
38400
and press [ENTER] to change
the baud rate.
I/F Mode (4C) ? appears.
21.
Press [ENTER] to accept
4C
(default setting)
as the entry.
If a different value appears in parentheses,
type
4C
and press [ENTER] to change the
value.
Flow (00) ? appears.
22.
Press [ENTER] to accept
00
(default setting)
as the entry.
If a different value appears in parentheses,
type
00
and press [ENTER] to change the
value.
Port No (13257) ? appears.
23.
For the Port number, type a number between
2000 and 10000, and press [ENTER].
If using two channels, set different port
numbers for Channel 1 and Channel 2
(shown in the Telnet configuration
screen).
ConnectMode (CC) ? appears.
24.
Press [ENTER] to accept
CC
(default setting)
as the entry, or type
CC
and press [ENTER]
to change the value.
Datagram Type (00) ? appears.
25.
If all field devices are using the same port
number as entered in
Step 23
, type
00
and
press [ENTER].
To use Datagram Type 02, Bosch
firmware version 6.5.8.0 or later is
required. Refer to the
Device Installer
Operation and Installation Guide
(P/N: 4998138688) for more
information.
26.
If all field devices are using unique port
numbers, type
02
and press [ENTER].
If Datagram Type 02 is used, enable it
in the D6600 Receiver refer to the
D6600 Program Entry Guide
(P/N: 4998122702).
For more information on Datagram
Types, refer to the
Conettix
D6600
System Guide
(P/N: 4998122712).