Bosch CL550 Configuration And Commissioning Software Manual Download Page 67

Page: 67 / 99

Commissioning Step by Step

4–1

1070 072 262-101 (01.09) GB

Commissioning Step by Step

The commissioning step by step describes the connection of a CL550 via the
TCP/IP protocol. The set values and addresses are transmitted into the sys-
tem controller using the project configurator.

Communication via the TCP/IP protocol takes place in a

single processor system via the ZS550, see page 4–3.

single processor system via the CON550 module, see page 4–7.

multiple processor system via the respective ZS550, see page 4–11.

multiple processor system via the CON550 module, see page 4–18.

Prerequisites

The following prerequisites have to be fulfilled for commissioning step by
step:

The components are physically connected with each other. For the
ZS550 it is necessary to take care that:

the data terminal equipment (PC, ZS550) has an MDI port

switches, hubs etc. have MID-X ports and a reversible port.

Depending on the communication parameters, a patch or cross-over cable
has to be used.

Device 1

MDI

MDI-X

Device 2

MDI

Cross-over cable

Patch cable

MDI-X

Patch cable

Cross-over cable

The configuration file is defined in the project configurator

The configuration of the PROFIBUS-DP is created in WinDP

The PLC program is created with WinSPS

Summary of Contents for CL550




































































































Search results

Summary of Contents for CL550

Reviews:

Related manuals for CL550

Brands by name

Popular brands

Bosch CL550, Configuration And Commissioning Software Manual

Search results

Summary of Contents for CL550

Reviews:

Related manuals for CL550

Brands by name

Popular brands