Bosch CL5000SCI 18-2 DCT/OU Installation Manual Download Page 3

Page: 3 / 28

Climate 5000 SCI – 6720887422 (2019/07)

Accessories

Accessories

The air conditioning system comes with the following accessories. Use all of the installation parts and accessories to install the air conditioner. Improper

installation may result in water leakage, electrical shock and fire, or equipment failure.

Name

Shape

Quantity

Tubing & Fittings

Soundproof / insulation sheath

Seal sponge (some models)

Orifice (some models)

Drainpipe Fittings

(for cooling & heating)

Drain joint (some models)

Seal ring (some models)

EMC Magnetic Ring

(some models)

Magnetic ring
(wrap the electric wires S1 & S2 ( P & Q

& E ) around the magnetic ring twice)

Magnetic ring
(Hitch the connective cable between

the indoor unit and outdoor unit after

installation.)

Others

Owner‘s manual

_____________________

Installation manual

_____________________

Transfer connector (Ø12.7-Ø15.9)
(Packed with the indoor unit )
NOTE: Pipe size may differ from appli-

ance to appliance. To meet different pipe

size requirements, sometimes the pipe

connections need a transfer connector

installed on the outdoor unit.

1 (on some models)

Transfer connector (Ø6.35-Ø9.52)
(Packed with the indoor unit)
NOTE: Pipe size may differ from appli-

ance to appliance. To meet different pipe

size requirements, sometimes the pipe

connections need a transfer connector

installed on the outdoor unit.

1 (on some models)

Transfer connector (Ø9.52-Ø12.7)
(Packed with the indoor unit, used for

multi-type models only)
NOTE: Pipe size may differ from appli-

ance to appliance. To meet different pipe

size requirements, sometimes the pipe

connections need a transfer connector

installed on the outdoor unit.

1 (on some models)

Connecting wire for display (2 m)

_____________________

1 (on some models)

Cord protection rubber ring

1 (on some models)

Table 1.

Optional accessories

•

There are two types of remote controls: wired and wireless.

Select a remote controller based on customer preferences and requirements and install in an appropriate place.

Refer to catalogues and technical literature for guidance on selecting a suitable remote controller.

Summary of Contents for CL5000SCI 18-2 DCT/OU





























Search results

Summary of Contents for CL5000SCI 18-2 DCT/OU

Reviews:

Related manuals for CL5000SCI 18-2 DCT/OU

Brands by name

Popular brands

Bosch CL5000SCI 18-2 DCT/OU, Installation Manual

Search results

Summary of Contents for CL5000SCI 18-2 DCT/OU

Reviews:

Related manuals for CL5000SCI 18-2 DCT/OU

Brands by name

Popular brands