en
Figure
Fit an accessory to either the flexible
tube or the telescopic tube.
a)
Crevice nozzle
For cleaning crevices and corners.
b)
Upholstery nozzle
For cleaning upholstered furniture,
curtains, etc.
Figure
a)
Switch off the vacuum cleaner.
b)
Insert the hose adapter back into the
holder.
c)
Press the rotary knob to release it and
turn it back to the floor tool position.
When the work is done
Figure
Unplug the vacuum cleaner.
Wind the cord around the power cord
hooks at the rear of the vacuum
cleaner.
Figure
a)
The vacuum cleaner can be hung by
the handle for storage.
b)
The vacuum cleaner can be
transported by the carrying handle.
Changing the dust bag
Replacing the dust bag
It is necessary to change the dust bag if
the dust bag change indicator appears
full when the nozzle is lifted from the
floor.
Figure
Open the lid in the direction of the
arrow, lift it away from the vacuum
cleaner and put it to one side.
11
10
9
8
7
Figure
Seal the dust bag by pulling the
sealing tab, remove the dust bag and
insert a new one.
!
Caution: The lid only closes with a
dust bag inserted.
After using the vacuum cleaner for
fine dust particles (such as plaster
or cement), clean the micro filter
and replace it if necessary.
If the dust bag change indicator still
appears full following the dust bag
change, it may be because the rotary
knob is blocked.
Figure
a)
Press the rotary knob to release it and
turn it to the position of the arrow.
Remove the rotary knob and shake it
b)
Refit the rotary knob and, while
pressing it down, turn it back to the
vacuum position required.
Replacing the micro-hygiene filter
Replacement is required:Each time you
need to open the replacement filter
pack.
Figure
Open the lid (see Figure 11).
Pull out the filter holder and open it.
Dispose of the micro-hygiene filter
and fit a new micro-hygiene filter.
Insert the filter holder back into the
vacuum cleaner and close the lid
14
13
12
en
Fold out picture pages.
Setting up
Version A
Engage the handle in the telescopic
tube.
To remove the handle, press the notch
button and pull the handle out of the
telescopic tube.
Turn the locking ring on the vacuum
cleaner to position
and insert the
telescopic tube in the opening.
Lock the telescopic tube in place by
turning the ring to position .
To remove the telescopic tube, move
the ring back to position
and pull
out the telescopic tube.
Connect the floor tool to the vacuum
cleaner.
Version B
Turn the locking ring on the vacuum
cleaner to position
and insert the
handle in the opening.
Lock the handle in place by turning
the ring to position .
To remove the handle, move the ring
back to position
and pull out the
handle.
Fit the telescopic tube to the vacuum
cleaner.
Connect the floor tool to the
telescopic tube.
ELECTROMATIC
®
brush
Your vacuum cleaner is equipped with
an ELECTROMATIC
®
brush. For notes on
use and maintenance, please refer to the
accompanying instruction manual.
Figure
Press the adjusting sleeve in the
direction of the arrow and adjust the
telescopic tube to the length required.
Figure
Release the lower power cord hook
by turning it and remove the cord
from the upper power cord hook.
Connect the plug to the mains socket.
Figure
Turn the vacuum cleaner on/off at the
switch.
Figure
Adjust the suction setting by turning
the rotary control.
Vacuuming
Figure
Adjusting the floor tool:
Rugs and
carpets
=>
Hard surfaces
=>
Vacuum using flexible tube
Figure
a)
Switch off the vacuum cleaner.
b)
Press the rotary knob in the direction
of the arrow to release it and set it to
the flexible tube position.
c)
Pull the hose adapter out of the
holder in the direction of the arrow.
6
5
4
3
2
1
