Bosch BGL4 Series, Operating Instructions Manual

Page: 40 / 120

39
Figure
a) Insert the telescopic tube into the connecting piece
of the floor tool. To release the connection, turn the
tube slightly and pull it out of the floor tool.
b) Push the telescopic tube into the connecting piece of
the floor tool until it locks in place. To release the
connection, press on the locking collar and pull out
the telescopic tube.
Figure
●
Move the adjusting sleeve/slider button in the direc-
tion of the arrow to unlock the telescopic tube and
adjust it to the length required.
Figure
●
Attach the accessories holder to the multi-purpose
nozzle and clip it onto the suction pipe/telescopic
tube.
Figure
Holding the power cord by the plug, pull out to the
required length and insert the plug into the mains
socket.
Figure Switching on and off
●
Press the ON/OFF button in the direction of the
arrow to switch your vacuum cleaner on.
Figure Controlling the suction level
The suction level can be in finitely adjusted to the level
required by turning the control knob in the direction of
the arrow.
Low power range =>
For vacuuming delicate materials, e.g.
upholstery, curtains, etc.
Medium power range =>
For the daily vacuuming of light
dirt deposits.
High power range =>
For vacuuming durable floor coverings,
hard floors and heavily soiled surfaces.
Vacuuming
! Please note:
Floor tools are subject to a certain amount of wear,
depending on the type of hard floor you have (e.g.
rough, rustic tiles). Therefore, you must check the
underside of the floor tool at regular intervals. Worn
undersides of floor tools may have sharp edges that
can damage sensitive hard floors, such as parquet or
linoleum. The manufacturer does not accept any
responsibility for damage caused by worn floor tools.
Figure
Set the adjustable floor tool:
Rugs and carpets =>
Hard floors =>
5
6*
7
8
9
10
4* If you are vacuuming up relatively large particles, make
sure that you vacuum them up successively and
carefully to ensure that the vacuum channel of the floor
tool does not become blocked. If necessary, you should
raise the nozzle in order to better vacuum up the dirt
particles.
Figure Vacuuming with accessories
Attach the nozzles to the suction pipe or hand grip as
required:
a) Crevice nozzle for vacuuming crevices and corners,
etc.
b) Upholstery nozzle for vacuuming upholstered
furniture, curtains, etc.
c) Hard-floor tool
For vacuuming hard floor coverings
(tiles, parquet flooring, etc.)
●
Push the telescopic tube into the connecting piece of
the hard floor tool until it locks in place.
●
To release the connection, press the locking collar
and pull out the telescopic tube.
Figure Cleaning the hard-floor tool
a) Vacuum the tool from below to clean it.
b) Use scissors to cut through threads and hairs wound
round the rollers and then vacuum them away.
Drill dust nozzle
Figure
a) Secure the drill dust nozzle to the handle and then
place against the wall, so that the nozzle drill hole
opening sits directly over the hole to be drilled.
b) Select the lowest power setting and then switch on
the vacuum cleaner.
Suction holds the drill dust nozzle in the required
position.
c) Depending on the surface of the wall to be drilled it
may be necessary to readjust the power to a higher
setting to ensure the drill dust nozzle is firmly
attached.
Any fine particles are automatically vacuumed up.
Turbo brush
If your appliance is equipped with a turbo brush,
consult the accompanying instruction manual for
instructions on its use and maintenance.
Figure
You can use the parking aid on the back of the vacuum
cleaner if you wish to stop vacuuming for a short time.
●
Once you have switched off the appliance, slide the
hook on the floor tool into the recess on the rear of
the appliance.
Figure
To overcome obstacles, e.g. steps, the appliance can
also be carried by the handle on the appliance body.
11*
12*
13*
14
15
*depending on model
GA 9000 953 348_1_GL4 20.06.2014 10:37 Seite 39