background image

SBA8230-1

Rev. 10/11

CONDENSING GAS WATER HEATER

Owner’s Guide

*SBA8230   T*

Robert Bosch (Australia) Pty. Ltd.

Thank you for purchasing this Bosch Condensing Gas Water Heater.
Before using, please:
Read this manual completely for operation instructions.
Confirm warranty and proof of purchase.
Keep this manual where it can be found whenever necessary.
This appliance must be installed in accordance with the manufacturer's installation instructions, AS
5601, NZ 5261, AS3500.4.2 and all Local Water, Building and Gas fitting regulations.
Bosch reserves the right to discontinue, or change at any time, the designs and/or specifications of
its products without notice.

- Do not store or use petrol or other flammable vapours and liquids in the

vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier.

If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury, or death.

WARNING

- To be installed and serviced only by an authorised person
- This appliance is not suitable for use as a pool heater

Model BC3200RA

BC3200RA5

Operating Instructions

* Note : This appliance requires a minimum flow rate to operate of 2.5 litres/min., water fixtures with a

flow rate of 7.5 litres/min. or higher are recommended.
For optimum performance we reommend installation of Bosch optional temperature controllers.

             

[Check Water Supply Quality]

If the water supply is hard, acidic or otherwise impure, treat the water with approved
methods in order to ensure full warranty coverage.

Summary of Contents for BC3200RA









































Reviews: