background image

SAR8872-2

Rev. 10/11

CONDENSING GAS WATER HEATER

Owner’s Guide

*SAR8872   T*

Robert Bosch (Australia) Pty. Ltd.

Thank you for purchasing this Bosch Condensing Gas Water Heater.
Before using, please:
Read this manual completely for operation instructions.
Confirm warranty and proof of purchase.
Keep this manual where it can be found whenever necessary.
Installation must conform with local codes, or in the absence of local codes, AS5601, AS/
NZS3500.4, AS3000 wiring regulations and all Local Building, Water and Gas fitting regulations.
Bosch reserves the right to discontinue, or change at any time, the designs and/or specifications of
its products without notice.

- Do not store or use petrol or other flammable vapours and liquids in the

vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier.

If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury, or death.

WARNING

- To be installed and serviced only by an authorised person
- This appliance is not suitable for use as a pool heater

Bosch Eco26+

Model  BC2600RA

Operating Instructions

* Note : This appliance requires a minimum flow rate to operate of 2.5 litres/min., water fixtures with a

flow rate of 7.5 litres/min. or higher are recommended.
For optimum performance we reommend installation of Bosch optional temperature controllers.

Summary of Contents for BC2600RA





































Reviews: