background image

70

en | Communication Configuration

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

Selections

: 0-30 ASCII characters

Enter up to 30 ASCII characters for the Network Access Point password.
The password is case sensitive.

USB Menu Location

[3] Advanced Communication Configuration > [4] Cellular Setup > [1] Cellular Plug-in Module
> [3] Network Access Point Password

7.11.4

SIM PIN

Default

: Blank

Selections

: 4-8 numbers

Use this parameter only for SIM cards requiring a PIN.
If a SIM PIN is not required, leave the field blank.
The SIM PIN appears as asterisks (********) as you enter it. If you enter an invalid SIM PIN, an
event is logged. A report is sent only if the report function is enabled.

USB Menu Location

[3] Advanced Communication Configuration > [4] Cellular Setup > [1] Cellular Plug-in Module
> [4] SIM PIN

7.11.5

Inbound SMS

Default

: Enabled

Selections

:

Enabled - the B465 processes inbound SMS text messages.

Disabled - the B465 does not process inbound SMS text messages.

USB Menu Location

[3] Advanced Communication Configuration > [4] Cellular Setup > [2] Inbound SMS

7.11.6

Reporting Delay for Low Signal Strength (minutes)

Default

: 0

Selections

: 0 (disabled) - 60 (minutes)

Time in minutes of low signal strength (red LED on cellular communicator) before the control
panel creates a Cellular Low Signal event.
Low signal is defined as 80% of the measurements taken during the time period are below the
threshold).
The B465 creates a Cellular Low Signal Restoral event when the signal strength is good (green
LED on cellular communicator) for the number of seconds this Reporting Delay for Low Signal
Strength parameter.
Good signal is defined as 80% of the measurements taken during the time period are above
the threshold.

Notice!
UL Requirement

To meet UL requirements, the entry for this parameter should not exceed 3 minutes.

USB Menu Location

[3] Advanced Communication Configuration > [4] Cellular Setup > [3] Reporting Delay for Low
Signal Strength (min.)

7.11.7

Reporting Delay for No Towers (minutes)

Default

: 0

Selections

: 0 (disabled) - 60 (minutes)

Summary of Contents for B465




















































































































Reviews: