background image

60

en | Communication Configuration

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

7.6

Cloud (Remote Connect)

Use the parameters in this section to configure the B465 to connect to RPS using Remote
Connect (Cloud) service for Ethernet IP or Cellular IP communication.

7.6.1

Cloud (Remote Connect) Ethernet

Default

:

 

Disabled

Selections

:

Enabled - use the on-board Ethernet connector for Cloud (Remote Connect) connections.

Disabled - do not use the on-board Ethernet connector.

Remote Connect is a Bosch Cloud-based Service that allows RPS to connect to the B465 for
programming and diagnostics.

Notice!
Bosch Installer Services, Remote Connect subscription required

Before you can use Remote Connect for RPS connections you need to visit https://
installerservices.boschsecurity.com/
 to sign up for Bosch Installer Services.

USB Menu Location

[3] Advanced Communication Configuration > [1] Account Setup > [7} Cloud (Remote
Connect) Ethernet

7.6.2

Cloud (Remote Connect) Cellular

Default

:

 

Disabled

Selections

:

Enabled - use an optional plug-in cellular communicator for Cloud (Remote Connect)
connections.

Disabled - do not use an optional plug-in cellular communicator.

Remote Connect is a Bosch Cloud-based Service that allows RPS to connect to the B465 for
programming and diagnostics.

Notice!
Bosch Installer Services, Remote Connect subscription required

Before you can use Remote Connect for RPS connections you need to visit https://
installerservices.boschsecurity.com/
 to sign up for Bosch Installer Services.

Notice!
Cellular is back up when both Cloud (Remote Connect) Ethernet and 
Cloud (Remote Connect) Celluar are enabled.

When both the Cloud (Remote Connect) Ethernet and Cloud (Remote Connect) Celluar
parameters are set to Enabled, the B465 only uses the cellular cloud connection if the
Ethernet cloud connection fails.

USB Menu Location

[3] Advanced Communication Configuration > [1] Account Setup > [8} Cloud (Remote
Connect) Cellular

7.7

Primary Receiver

You can configure the B465 to send reports to one or two central station receivers (primary
receiver, secondary receiver). Use the parameters in this section to configure for the primary
receiver.

Summary of Contents for B465




















































































































Reviews: