Bosch ARD-AYCE65B Installation Manual Download Page 6

Page: 6 / 32

en | Technical Specifications

ARD-AYCE65B

| V 1.1 | 2009.08

Installation manual

Bosch Sicherheitssysteme GmbH

Technical Specifications

Specifications

ARD-AYCE65B

Electrical Characteristics
Power supply type

Linear type - recommended

Operating voltage range

5 - 16VDC

Input current standby

92mA@12VDC

max Input current

105mA@16VDC

LED control input

Dry contact N.O.

Tamper output

Open collector, active low, 30mA
max sink current

Cable distance to host
controller

Up to 500ft (150 meters) using an
18AWG cable

Max proximity card read
range*

40mm (1.575 inch)

Proximity card
modulation

ASK at 125 KHz

Proximity card
compatibility

EM cards

Card Transmit format
(Reader)

26-bit Wiegand, or Clock & Data

Keypad Transmit Format
(Reader)

Programmable PIN code formats

LED indicators

Two tri-colored LEDs

Communication

Data1/Clock, Data0/Data- TTL
output

Environmental Characteristics
Operating temp. range

-30 to 65° C (-22 to 150° F)

Operating humidity

0 - 95% (non-condensing)

Outdoor usage

Weather-resistant, meets IP-68,
epoxy potted, suitable for outdoor
use

Mechanical

Summary of Contents for ARD-AYCE65B

































Search results

Summary of Contents for ARD-AYCE65B

Reviews:

Related manuals for ARD-AYCE65B

Brands by name

Popular brands

Bosch ARD-AYCE65B, Installation Manual

Search results

Summary of Contents for ARD-AYCE65B

Reviews:

Related manuals for ARD-AYCE65B

Brands by name

Popular brands