Bosch ACS 251 Original Instructions Manual Download Page 16

F 002 DG9 425

2014-03-20

Bosch Limited

16  |  ACS 251  |  Program description

en

6.6 

Manual mode

6.6.1 

Overview of manual mode

In the manual mode, only the selected phase is ex-
ecuted. For example, upon selecting "

Recovery

", only 

the recovery phase will be executed. It is also possible 
more than one service phase.
The default values of the parameters in each stage are 
listed in the following table:

Service phase

Parameter

Default value

Recovery

Pressure increase time

1 min

Vacuum

Vacuum time

20 min

Vacuum hold time

4 min

Oil recharge

Refrigerant quantity

500 g
10 ml

Oil quantity

Tab. 1: 

Default values of parameters

6.6.2 

Recovery

In the recovery phase, the following parameters can be 
set:

 

R

Duration for the pressure increase test

 

R

Hose selection

 

$

HP hose

 

$

LP hose

 

$

HP and LP hoses

6.6.3 

Vacuuming phase

In the recovery phase, the following parameters can be 
set:

 

R

Vacuum creation time

 

R

Vacuum test time

 

R

Hose selection

 

$

HP hose

 

$

LP hose

 

$

HP and LP hoses

 

i

Ensure that you perform recovery before the vacu-
uming.

6.6.4 

Oil recharge phase

In the oil recharge phase, the following parameters can 
be set:

 

R

Oil quantity

 

R

Refrigerant quantity

 

R

Hose selection

 

$

HP hose

 

$

LP hose

 

$

HP and LP hoses

 

i

Oil injection can only be carried out on an A/C sys-
tem that is under vacuum. 

 

i

Every time oil is recharged, R134a is also recharged.

 

i

The quantity of oil added to the vehicle A/C system 
corresponds to the quantity drawn during the recov-
ery phase. When filling a vehicle A/C system for the 
first time, refer to the vehicle documentation or the 
vehicle-specific repair manual for the specified oil 
recharge quantity.

 

i

Use oil grade specified by the vehicle manufacturer. 
Use only new oil to replace the oil removed during 
the recovery process. Used oil should be discarded 
as per local regulations.

6.6.5 

Recharge phase

In the recharge phase, the following parameters can be 
set:

 

R

Refrigerant quantity

 

R

Hose selection

 

$

HP hose

 

$

LP hose

 

$

HP and LP hoses

6.7 

Performing service in manual mode

 

!

Use only new oil to replace the amount removed dur-
ing the recovery process. Used oil should be discard-
ed as per applicable regulations.

1. 

In the main menu, select "

A/C Services

". Alternative-

ly, press the 

MANUAL

 button on the keypad.

 

i

If you press the 

MANUAL

 button, skip to step 3.

2. 

Select "

Manual Mode

" and press 

E

.

 

The phases that can be executed in the manual 
mode are displayed on the screen.

3. 

Press the 

o

 or 

u

 keys to scroll to a particular phase. 

To select a particular phase or multiple phases for 
execution, press 

.

4. 

Press 

E

.

 

The service parameters for the selected phases 
are displayed.

5. 

Set the values of the service parameters.

6. 

Check the type of connection on the vehicle  
A/C system.

7. 

Connect the appropriate coupler/s to the service 
connection on the vehicle A/C system.

 

!

Do not use any tools to tighten the couplers.

 

!

Always pay attention to the vehicle-specific info be-
fore changing the quantity of oil and R134a.

8. 

Press 

E

.

 

The selected service phase starts. At the end of 
the service, 

Hose Drain

 menu is displayed.

Summary of Contents for ACS 251

























Reviews: