background image

F 002 DG9 448

2018-02-01

Bosch Limited

14  |  ACS 151  |  Program description

en

6. 

Program description

6.1 

Preparations for A/C service

 

!

The ACS 151 should not be used for servicing a vehi-
cle A/C system that has been repaired with a chemi-
cal sealant. The sealant could damage the ACS 151 
and the vehicle A/C system. Non-compliance invali-
dates the warranty.

 

!

Do not attempt to shut off the valves on the R134a 
tank when the ACS 151 is in operation.

Before servicing the vehicle A/C system, execute the 
following preparatory procedure:

1. 

Move the ACS 151 to a flat vibration-free surface 
close to the vehicle.

2. 

Apply the brakes to prevent the ACS 151 from rolling 
away.

Caution!

Hot engine parts can cause severe burns to 
the hands.

 

Allow the engine to cool down before 
work.

3. 

Connect the power cable to the mains supply.

4. 

Turn on the master switch.

6.2 

Performing vehicle A/C service

The default values of the parameters in each stage are 
listed in the following table:

Service phase

Parameter

Default value

Recovery

Pressure increase time

2 min

Vacuum

Vacuum time

20 min

Vacuum hold time

5 min

Tab. 1: 

Default values of parameters

6.2.1 

Recovery phase

To execute the recovery phase, press the 

REC

 button 

on the keypad and skip to step 3 in the following pro-
cedure. Else, start from the main menu and execute all 
the steps in the following procedure.

Step Press 

key...

To...

Remarks

1

1

Select 

A/C SER-

VICES

--

2

1

Select

 BASIC

--

3

1

Select

 REC

The message 

CHECK 

OIL BOTTLE 

AVAILABILITY

 is  

displayed. Check if the 

oil bottle is fixed.

4

Enter

Execute the instruc-

tion on the screen.

The message 

OPEN HP

 

& LP VALVES

 is dis-

played.

5

Enter

Execute the instruc-

tion on the screen.

The message 

ENSURE 

OIL VALVE IS 

CLOSED

 is displayed.

6

Enter

Start recovery

Quantity of the refriger-

ant is displayed.

 

"

You have successfully completed the recovery phase. 
Press Enter to return to the main menu.

6.2.2 

Vacuuming phase

 

i

Ensure that you perform recovery before vacuuming.

To execute the vacuuming phase, press the 

VAC

 button 

on the keypad and skip to step 3 in the following proce-
dure. 

 

i

Upon pressing the 

VAC

 button, the fields 

VAC CREA

 

(vacuum creation time) and 

VAC HOLD

 (vacuum 

hold time) are displayed. Set the values and proceed 
to step 3 in the following procedure.

Else, start from the main menu and execute all the 
steps in the following procedure.

Step Press 

key...

To...

Remarks

1

1

Select 

A/C SERVICES

--

2

1

Select

 BASIC

--

3

2

Select 

VAC.

Set values for 

VAC CREA

 

VAC HOLD

The fields 

VAC 

CREA

 (vacuum 

creation time) and 

VAC HOLD

 (vac-

uum hold time) are 

displayed.

4

Enter

Execute the instruction 

on the screen.

--

5

Enter

Execute the instruction 

on the screen.

--

6

Enter

Vacuuming starts. Once 

the vacuuming is com-

plete, the vacuum hold 

starts. Then execute the 

instruction on the screen.

Observe the vacu-

um pressure on the 

screen.

 

"

You have successfully completed the vacuuming phase. 

Summary of Contents for ACS 151





















Reviews: