Bosch A20V(L)O Instruction Manual Download | Manualshive

Page: 56 / 68

background image

56/68

Maintenance and repair

Bosch Rexroth AG

, A20V(L)O Series 1, RE 93100-01-B/2019-09-10

10.4 Repair

Bosch Rexroth offers a comprehensive range of services for the repair of Rexroth
axial piston units.
Repairs on the axial piston unit and its assembled parts should only be performed
by service centers certified by Bosch Rexroth.

▶

Only use original spare parts from Rexroth to repair the Rexroth axial piston units,
otherwise the functional reliability of the axial piston unit cannot be guaranteed
and the warranty will be voided.

For questions regarding repairs, contact your proper Bosch Rexroth service partner
or the service department of the plant that manufactured the axial piston unit;
see chapter 10.5 "Spare parts" on page 56.

10.5 Spare parts

CAUTION

Use of unsuitable spare parts!

Spare parts that do not meet the technical requirements specified
by Bosch Rexroth can cause injury and property damage!

▶

Only use original spare parts from Rexroth to repair the Rexroth axial
piston units, otherwise the functional reliability of the axial piston unit cannot
be guaranteed and the warranty will be voided.

The spare parts lists for axial piston units are order-specific. When ordering
spare parts, specify the material and serial number of the axial piston unit as well
as the material numbers of the spare parts.
Address all questions regarding spare parts to your proper Bosch Rexroth Service
partner or the service department of the plant that manufactured the axial
piston unit.
Details for the manufacturer's plant can be found on the name plate of the axial
piston unit.

Bosch Rexroth AG
Glockeraustraße 4
89275 Elchingen, Germany
H49 9352 405060

Bosch Rexroth AG
An den Kelterwiesen 14
72160 Horb a.N., Germany
H49 9352 405060

Spare parts can be found online at

www.boschrexroth.com/eshop

For general inquiries, please contact your local contact person. You can find their
contact information at

www.boschrexroth.com/addresses

«
...
54
55
56
57
58
...
»

Summary of Contents for A20V(L)O





































































Reviews:

No comments

Related manuals for A20V(L)O

Brand: Kärcher Pages: 8

Brand: Daewoo Pages: 38

Goulds CentriPro M05411

Brand: Xylem Pages: 68

Brand: BLACKMER Pages: 24

Brand: TOHATSU Pages: 87

Brand: German pool Pages: 17

NEXIS-VE Series

Brand: salmson Pages: 120

Brand: Waterax Pages: 5

Brand: Enviro Pages: 112

3D TRASAR Series

Brand: Nalco Pages: 243

Brand: SHG Pages: 32

Digital-Flo DFS1540

Brand: Armstrong Pages: 44

Brand: BIANCO PUMPZ Pages: 7

AquaMax Eco Series

Brand: Oase Pages: 16

Modular S-N Series

Brand: Desmi Pages: 20

Brand: Flux Pages: 28

AJ 4 Plus 95/40

Brand: T.I.P. Pages: 140

AquaMax Eco Titanium 50000

Brand: Oase Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands